Result:

90195. - will it fit 2019 Ford ranger | Yes, the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 will fit and work perfectly on your 2019 Ford Ranger. There is not a factory plug-in port beneath the dash of your Ranger for a brake controller...

Will this wiring harness work for a 2024 Ford Ranger Lariet? Is this something I could install myself? When will it be available? | Hey Daniel, The Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector - Preorder # C86RV is...

I have small rear camera mounted to the top of the license plate. I also have a flat 4-pin trailer connector that I would like to get power to the camera. How do I do that? I was thinking that I could use a compatible connector and only...

I have a continuous 10gauge wire between the wheels with electric brakes. I want to tap into that wire and run a single 10 gauge wire to my 7 blade trailer side connector. Ground wires are grounded to frame at the wheels. Question: what’s the...

Is there anything special about manually adjusting self adjusting trailer brakes? I notice there are 2 little openings in rear of backing plate. One has the wheel. What’s the other opening for? Do I have to move the self adjuster out of the...

Hello, I have 2024 Ford Ranger Raptor and was wondering if this would fit since i have the raptor? Part RAS29VR. Was also wondering if they have air bags instead. I have a trailer that’s 4,500 pounds that i haul and I’m looking to get more stability...

I purchased a Curt Echo for my 2021 Ford ranger and when I set it up the app cant find the TBC. It looks like when its plugged into the 7 pin that it isnt getting power. I tried putting the truck in tow/haul mode thinking that might send power...

Never worked with Nev R Adjust brakes before, over tightened them, now they are bound tight and are frozen to the shoe. How can you back them off? | If you can pull the hub off that is going to be the easiest way to adjust the brakes looser...

By telling me how to figure out the spindle size and what hubs i need. | There's a few things you need to know that will tell you which hub fit your trailer's spindles. The first is your bolt pattern. I've attached a help article on measuring...

HAVE SIGNAL BRAKE FLASHERS BUT NO TAIL LIGHTS HAVE NO POWER AT THE PLUG CANT FIND A BLOWN FUSE HELP | Since you have brake and turn but not taillights, the issue can be a fuse, a relay, bad wiring, or a weak connection. I recommend you first...

My trailer is a 96 jayco popup that has a 6 wire plug and p/u has a 7 plug flat but cant get brake lights to work | Whenever any type of adapter like # PK12716 is used to mate different types of connectors on the vehicle and trailer, connection...

I just installed Curt T connector 7 way wiring harness #56431. Now I need to install a trailer brake. Will RedArc #RED44FR work with this harness and my 2019 Ford Ranger. | Thank you for purchasing the Curt T-Connector Vehicle Wiring Harness...

Hi there, Ive got a tandem flatdeck trailer with Dexter brake assemblies all around. During a recent routine check of my braking system I found that only 1 hub had any braking. Upon further checking I found that the hub that was braking Was...

Please help me, I need a brake controller and hopefully a wiring adapter for a 1998 Ford Ranger 4.0 liter engine, 4x4 Xlt ext cab truck, I am pulling a 17ft camper weighing 2750 dry weight. I am almost sure it has the towing package, It...

Which 2019 Ranger fuse feeds the always hot pin of the 7 pin trailer socket? | I looked up the online owners manual for a 2019 Ford Ranger. This shows the fuse for the trailer module is in spot 73 and it will be a 30 amp fuse. These newer ford...

Have a 1998 ford range, vehicle lights all working fine. Vehicle equipped with factory tow harness receptacle. When connected to trailer only right side works fine running brake turn and flasher and on left side only running lights. Trailers...

I have a 2001 Ford Ranger 4.0 and want to tow a 5000 gvw trailer a short distances less than 50 miles. My Ranger has the flat 4 way connector and the Trailer has a 9 way round connection. Is there a 4 to 9 adapter that feeds all the electrical...

My question is concerning a M416 military trailer. My intention are to change the hub and drum to get a 5x5 bold pattern. Thanks for your help! | Thanks for the picture! To determine the correct replacement hub to give your M416 military trailer...

I have the C11580 . I have 2019 Ford Ranger. I cant get it to work. My power tab is at 5 oclock position. The controller goes in upside down. Do u have a solution? | It sounds like there may be an issue with the fuse or wiring on your 2019...

I installed a universal trailer lighting kit on mt trailer, i drive a 1999 ford ranger, once i connect the harness from trailer to truck i can only get runnig light, no turn signals, not sure if my truck is equipped with independent bulb turn...

I have a 2005 Ranger 185DVS and ranger trail single axle trailer. It has disc brake and I need a complete hub assembly. Ranger gave me a part # of 9606003R1. Do you have this part available. I have oil hubs now, I think this part #is for grease...

Would like to install parts for my 2006 trailer. casita 17ft deluxe freedom brake kit RandL want to order kits for this trailer please advise part number needed. The Dexter axle model is 10H, The weight capacity is 3500 lbs. I would like manual...

This is a little off topic from this Redarc brake controller but somewhat similar. I see that the Redarc has a separate adjustment knob that you mount wherever desired. The knob then plugs into the control box and the Ranger factory wiring gets...

I have 5 wires coming from the truck, red, green, yellow, Brown and white, your kit 48205 does not have place for red wire. Do I need different model number or what to do with red wire? 1994 Ford Ranger | To install the Hopkins 4-Way Flat Trailer...