!Wildcat Maxx Travel Trailer  x   >   !Excalibur  x   >   MORryde  x   >  

MORryde RV Cargo Sliding Tray - 90 x 42 - 2 Way Slide - 60 Percent Extension - 800 lbs Does this tray come in Black? | The 90" x 42" MORryde RV Cargo Sliding Tray # MR35FR is only offered in the gray finish. |

2010 Keystone Montana 2955RL 5th wheel. 28 1/4 wide, 30 inch to ground and 9 inch deep before step up into camper. Will the MR68RR work for my application? | Hey Rick, Yep, the 3-step MORryde StepAbove RV Steps # MR68RR will indeed work for...

I am looking for springs for my fifth-wheel tailer, Here are the numbers off of the axle. lci60-sb-89-70.75-spob-os-l-655-7226 NV 136338 MFg Date 01-27-07 GAWR 6000 Lbs Serial 352336 2007 Fleetwood Redline 33 Toyhauler. Can you send me a list...

Hello, I would like to install the XF12-001 X-Factor cross member. I have a drain line in the way. Is the XF12-003 MR43WR the correct bracket kit to lower the cross member to avoid the drain line? | It is likely you can avoid the drain line...

Is there an x-factor for the alltrek 4000? | Since the MORryde AllTrek 4000 Equalizers # MR29DR sits inside the middle hanger like a standard equalizer you'd want to use the MORryde X-Factor Crossmember for Standard Frame Hangers # MR33WR. This...

I just recently purchased a Jayco north point 5th wheel. It came with the cre 3000 already on it and I added the sumo springs also. Would I notice any ride quality improvement by swapping out the cre 3000 for the alltrek 4000? | The AllTrek...

I have a 2014 SureTrac Tilt Equipment Trailer. Dual Axle. My current shackles are 3 1/4 inch Center to Center. The kit I was looking at says 3-1/8. I did not seem to find a kit with 3 1/4. This kit seem to be ok with only the 1/8 inch difference? Thank...

do you have the replacement SHEAR SPRING available? | We do a couple replacement shear springs available for you that may work depending on what you're needing. For instance, we do carry the Replacement #75 Rubber Shear Spring for MORryde Trailer...

We bought a Grand Design 303RSL with a Morryde Flip Step installation. Dealer sold us the Handrail for a 2nd gen step... however I found that there isnt any readily available installation instructions for the handrail with these steps. So, has...

Looking for a lift assist kit for a 4 step above width of door 30 in width of steps is 27 in outside to outside. inquiring if you have this. Thanks | The MORryde StepAbove entry steps install inside your camper's doorframe, measure...

I have Jayco 29RLDS with 2 4400lb. axles. I ordered wet bolts/shackles and MR87ZR. My axles measure 35inch center to center. My FHS measurement is 58 3/4. Did I the right equalizer or should I have 35inch MR27ZR. I think my springs are 26inch...

I need to replace my leaf springs and equalizer on my 2021 Coachmen 259FKDS. What do I need to measure to get the correct items? | The determine the correct replacement leaf spring on your 2021 Coachmen 259FKDS you'll need to lift your trailer...

Do you sell the MORryde ALLTrek 4000 equalizer? | We do carry the MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers # MR29DR. This is going to be their 35" wheelbase version which is going to be 8" from center of front shackle mounting...

What is the height from the trailer floor to the bottom of the the tray? Will it clear by trailer door opening, I need 2 1/2” to clear for the tray to extend out. Thank you, | The MORryde RV Cargo Sliding Tray # MR87FR has a 1.57" clearance...

Getting some pretty loud clunksinch coming from the suspension so I started investigating the possible causes. I am the second owner, BTW It currently has a MORryde equalizer and greaseable shackles which I would assume are also MORryde. Just...

I have a curtA30 in bed and a Rota-flex pin box having clearance problems I would like to spec out a gen-y pin box can you help me select one I have a 2021 GMC Denali and a Vilano 394RK | Thank you for the information and photo! I was able...

What is the measurement from first mounting bolt towards front of the Rv to the fifth wheel hitch. Looking for something a bit longer for my turns in the Rv. Thank you | The MORryde Cushioned 5th Wheel Pin Box for 18K to 21K Trailers w/ Lippert...

I have a 2020 Coachmen Chaparral 336TSIK 5th wheel and am looking at upgrading the suspension with LIppert Road Armor equalizers. My current equalizers are Dexter 13-144. The horizontal shackle holes are 7 3/4inch apart, and the distance from...

Looking at the MoRyde CRE 3000 system. I note to measure ones axles for either the 33 inch or 35 inch. I have a Forrest River 31QBH with Lipper 5200# dual axles. As if following Murphys law, my axles measure almost 34 inch to top dead...

On the MORryde X-Factor Crossmember Adapter Kit, what is the distance from the outside of the mounting flange to where it breaks over for the ? | I reached out to MORryde for you and obtained the information that you requested for the MORryde...

I submitted a question on my 2015 Keystone carbon 327 I need some more information. my trailer is a tandem axle so i need part #s for the upgrade shackle kit my shackles measure 3 1/4 inch to the eye. I also need hanger brackets which measure...

Where can I purchase the Roadmaster 2630 ubolt kit, for 3 axles? | You can get the longer U-bolts here; I checked with Roadmaster, and the 2630 are simply 7 inch long U-bolts, so you can use the following: - 3" Round Trailer U-Bolts (Qty 2)...

I was going through the measurement qualifier process fo the Morryde Alltrek 4000 equalizer... I have all good numbers to qualify except I have a 35inch wheelbase with a 59inch leaf spring outer measurement on my dual axle 5th wheel trailer.. Which...

Im looking at upgrading my shackles on my 2020 Heartland Cyclone 4007 5th wheel. I only see an option for a tandem axle. Do you offer a triple axle option? Also, I currently have the CRE3000 equalizer, is the Road Armor considered an upgrade?...