Replacement Gear Recommendation for Fulton Trailer Jack

Question

Question:

Im trying to find replacement bevel gears for my Fulton jack but dont know its model number. The gear is 1-1/8 OD, 1/2 ID and just under 9/16 thick. I tried the 7002048-00 but it has an OD of 1-5/16 and is 5/8 thick. Can you point me in the right direction?

asked by: Steve A

0

Expert Reply:

Based on the dimensions you listed it sounds like you need the part # F0933302S00. The gear has an inner diameter of 1/2 inch and an outer diameter of 1-1/8 inches. I attached a picture that has all of the gear dimensions for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hi James; based on the information you have provided the only option we carry that might work is the Replacement Bevel Gear Kit for Fulton Jacks - 800 - 1,200 lbs #F0933302S00. You can compare what you have now to the attached picture with…

view full answer...

Answer 2

I went out to the warehouse and measured the gears for the Replacement Miter Gear for the Dutton-Lainson Trailer Jack. The diameter of both gears is 1-1/8 inches. The height of the taller gear with the circular center is 1/2 inch and the height of…

view full answer...

Answer 3

Yes, there is 15 teeth per each gear on the Replacement Gear Kit for etrailer and Ram Sidewind Jacks #TJA-2000S-GR. These gears have a thickness of 0.5", an OD of 1.36", and an ID of 0.5".

view full answer...

Answer 4

Hello Greg. We do carry the Fulton jacks, but I was not able to find any references to the part number 1413270334 you provided. Even the Fulton website does not show it. The most similar part number I can find is the Fulton #F1413250334. This is the…

view full answer...

Answer 5

I recommend replacing the jack as that part #9 that you referenced in the diagram is not replaceable according to Fulton. The Fulton F2 Swing-Up Trailer Jack #F1413040134 is a similar sidewind wide-wheel jack and will bolt onto a 3"x3" or…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Gear Recommendation for Fulton Trailer Jack

Continue Researching