What Wiring Harness and Trailer Hitch Fits a 1967 Ford F-250?
Updated 11/18/2026 | Published 11/16/2026 >
Products Featured in This Question
Question:
I have a 1967 F250 with a regular 7 pin RV plug in. I would like to buy a wiring harness for the tail, turn and brake lights plus the same for my modern RV 7 pin plug in. Can you help me with this? Also Ill need a heavy hitch rated 10,000 lbs or better for this 1967 4x4 f250 highway. Tell me what choices I have. Thank you, Gary M
asked by: Gary M
Expert Reply:
Hi Gary,
If you're needing wiring to tow your more modern RV the only wiring harness, we have for your vehicle is the Curt Trailer Wiring Harness w/4-flat part # C58044 that'll need to be spliced into the vehicle's wiring. It comes with quick splices, but I recommend using heat shrink butt connectors instead to make sure you have a waterproof connection. To get the 7-way wired up for towing your RV with brakes, you'll need to use the Universal Trailer Brake Controller Installation Kit part # ETBC7. This comes with a new 7-way connection that'll allow you to plug the 4-flat from the Curt wiring into it and then run the brake wire and power wire back to the 7-way, so it'll work with your RV. Which is nice because you'll have a functioning 4-way and 7-way with the new connector.
As for a trailer hitch, I'm not sure what bumper you have, but if you have a standard or step bumper you can use the B&W Heavy Duty Trailer Hitch part # BWHDRH25122. It only fits 34" and 37 1/2" frames so you'll want to measure your 1967 Ford's frame to make sure it'll fit. It has a 1,600lb tongue weight and 16,000lb tow capacity, which is more than what you'll need. There will be drilling involved and the spare tire may need to be removed if there isn't enough space after the hitch is installed.
If you have a deep drop bumper, you can use the B&W Heavy Duty Trailer Hitch part # BWHDRH25198. It has the same weight capacity as the other B&W hitch but is designed for the deepdrop bumper. It has the same 34" and 37 1/2" frame fitment, so you'll need to verify that either of these hitches will be a good fit.
Is your truck's current 7-way not wired? Or are you wanting to replace the wiring on it?
Product Page this Question was Asked From
B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- For Towing
- Class V
- 1600 lbs TW
- 16000 lbs GTW
- 16000 lbs WD GTW
- 2 Inch Hitch
- 1600 lbs WD TW
- Visible Cross Tube
- B and W
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Does Curt Hitch for 2026 Toyota Corolla Cross Also Fit Hybrid Models
- Q&A: What's The Difference Between the etrailer and Demco Baseplate 2025 Jeep Wrangler
- Q&A: Best Trailer Hitch And Wiring Harness For 2026 Nissan Rogue Dark Armor Edition
- Q&A: Replacement For 7-Way Socket That Came With ETBC7/ETBC7L Kit
- Q&A: Recommended Hitch for a 2026 Toyota Corolla Cross and How to Install It
- Q&A: Recommended Base Plate that Works With a 2024 Jeep Wrangler
- Q&A: Will the Demco Excali-bar 9511006 Work With the Demco Tabless Kit On Jeep Wrangler Unlimited
- Article: Which Hitches are Made in the USA
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: What RV AC Will Work With Your Setup? Avoid Costly Mistakes Before You Order
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: How to Measure for Trailer Hitch Drop
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size


Gary M.
11/16/2026
Hi, Thank you for the prompt reply! The hitch i have on it now is a draw-Tite and I think i bought it from etrailer.com The sticker it says 75034 and made in Mexico. Is this the 34" model? I measured inside to inside and it measures 33.5" My pickup doesn't have a rear bumper, so no worries there. I've got the wiring harnesses understood. So will the hitch you recommend work on my truck? If so, I'm good to go. Please confirm the hitch for me! Thank you, I appreciate the help! Gary Mann