Replacement Arms for a Falcon 2 Tow Bar
Updated 09/28/2026 | Published 09/27/2026 >
Products Featured in This Question
Question:
I would like the two arms as one of them doesn't lock any more. It has many miles on it. The serial number is 036142. I believe it is a RM-520. I don't want to have to buy the whole thing if possible.
asked by: Jody T
Expert Reply:
Thanks for the information Jody! To replace the arms of the Roadmaster Falcon 2 Tow Bar item # RM-520, you'll need the following parts:
Driver's Side - Replacement Inner/Outer Arm Assembly item # 910021-70
Passenger's Side - Replacement Inner/Outer Arm Assembly item # 910021-80
These parts will replace both your Falcon 2 Tow Bar item # RM-520 arms. They'll get your tow bar back up and running so you can get back on the road.
What kind of vehicle are you flat towing? Feel free to answer this and throw in any other questions you have, where it says Add Comment.
Product Page this Question was Asked From
etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Hitch Covers
- Misc Covers
- Plain
- Rubber
- Fits 2 Inch Hitch
- Standard
- Square
- etrailer
more information >
Continue Researching
- Q&A: Does Curt Hitch for 2026 Toyota Corolla Cross Also Fit Hybrid Models
- Q&A: What's The Difference Between the etrailer and Demco Baseplate 2025 Jeep Wrangler
- Q&A: Best Trailer Hitch And Wiring Harness For 2026 Nissan Rogue Dark Armor Edition
- Q&A: Replacement For 7-Way Socket That Came With ETBC7/ETBC7L Kit
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Will the Demco Excali-bar 9511006 Work With the Demco Tabless Kit On Jeep Wrangler Unlimited
- Q&A: Recommended Base Plate that Works With a 2024 Jeep Wrangler
- Q&A: Recommended Hitch for a 2026 Toyota Corolla Cross and How to Install It
- Article: Which Hitches are Made in the USA
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: What RV AC Will Work With Your Setup? Avoid Costly Mistakes Before You Order
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size



Jody T.
9/28/2026
Nice. I'm glad to see that they are available. I'm now deciding if I want to spend the $500+ for the parts and then have to do the work it will take to properly install them. Or buy the whole assembly and only have to install it into the receiver for $850. Plus the old one didn't hold well when you had it stowed, causing me to have to add extra securing straps. I have two different vehicles I tow, depending on where we are going. A 2016 Chevy equinox front wheel drive with a base plates and cross bar Or a 1996 jeep Cherokee XJ. 4x4 5 speed manual. I have to change out the ends of the tow bar to hook up to jeep bumper shackle mounts. I also bought the short safety cables, which I kind of permanently mounted to the bumper mounts to make it easier hook up the cables from the motorhome. When I'm not towing it, I just tuck them up behind the bumper. The jeep is much easier to get ready to tow and connect than the equinox with the installing parts on the front of the equinox and much harder to connect to the tow bar. But either vehicle being flat towed is way better than when I had a tow dolly. Tow dollies are fine, if you are less than 50 years old and can't find or afford a vehicle that can be flat towed. While flat towing is a little more expensive in the beginning with braking and insulation than a tow dolly initially. But you have to pay for registration for the trailer and then there's another set of tires and brakes in the future. I've had my tow bar set up for nearly 10 years on the equinox and the jeep since 2024. It's been to both coasts twice and Alaska (I towed the Jeep to Alaska, I thought it would be more appropriate to have a jeep than an equinox in Alaska and northern Canada) I live in MN.