bing tracking image
Q & A Icon

How to Lower a Boat on a Bunk Trailer for Easier Launching?  

Updated 10/02/2026 | Published 09/23/2026

Question:

I recently replaced my Shorelander with rollers with a SeaLion S-17-2200, with 8 foot bunks. My 1983 Sea Nymph CC171 sits 8 inches above the trailer frame, 16 inches off the pavement. I can hardly get it launched. I was considering using these roller bunks, with 2 by 4s and different bolsters. Any suggestions?

0

Expert Reply:

Hey Paul, thanks for reaching out. I think the Tie Down Roller Bunks # TD87FR are a good direction for what you are trying to fix.

I would not mount them on top of 2x4 bunks though, since your main problem is already that the boat sits too high. The # TD87FR can mount directly to the trailer frame or to adjustable bolster/swivel brackets, and that gives you a much better shot at lowering the hull while gaining the easier launch of rollers.

With the boat already sitting 8" above the frame, I would start by seeing how low you can position the rollers directly on adjustable brackets while still maintaining clearance between the hull and the trailer frame/fenders. That will do more for your launch height than putting rollers on top of the existing 2x4s.

Where do you usually launch your boat? Fresh or salt water?

expert reply by:
0
Jesse M
Tie Down Roller Bunks for Boat Trailers - 6 Rollers Each - Amber Poly - 5' Long
Tie Down Roller Bunks for Boat Trailers - 6 Rollers Each - Amber Poly - 5' Long
(click to enlarge)
Paul G. profile picture

Paul G.

9/24/2026

Thanks, Jesse. I launch in fresh water, and some of the ramps are shallow. In addition, I'm not getting any younger, and my days of muscling heavy stuff are long gone -- and the bunks on this new trailer definitely qualify as muscling! My 17' aluminum hull is 700 pounds empty, and is wearing a 60HP Merc 4-stroke. Tackle, gas, batteries and ( a BIG!) lunch might bring the whole rig to (maybe) 1500 pounds. The trailer has two 3" by 2" cross-members 72 & 1/2" apart. The existing 8-foot bunks hang about a foot over both forward and aft. I can't use either 5 foot or 4 foot roller bunks without a rail to span that distance, in particular to extend aft about a foot to support the transom. The bunks are 2-by PT with carpet sitting on 10 inch bolsters. My *CURRENT* theory is to mount four 2x4x8's on the cross beams , then use four 5' roller bunks to support the weight, staggered fore & aft, so the stern is supported, but the bow isn't hanging in mid-air. Plan "B" is to use 4 four footers. Plan "C" is to use some sort of center-line roller to support the bow. Complicated, huh?

Jesse M. profile picture
Etrailer Expert

Jesse M.

9/24/2026

@PaulG Honestly, the more detail you give me, the more I like your Plan A. With a roughly 1,500 lb loaded boat and those crossmembers 72-1/2" apart, using four 5' # TD87FR roller bunks staggered front and rear gives you good support along the hull while still getting the easier launching you are after. I also like the idea of adding the 2x4 cross supports if that gives you the mounting locations you need, just keep everything as low as possible so you do not give back the height you are trying to eliminate.
Paul G. profile picture

Paul G.

9/28/2026

Jesse -- a follow up, if I can bother you some more ... My estimate for the amount of rollers and hardware approaches $1000, and would seem to require quite a bit of DIY modifications for my recently purchased Sea Lion S-17-2200. What if I replaced the bolster brackets (currently 9 & 1/2" by 2 & 1/2") with shorter version ( TD54FR ? ) to lower the hull closer to the frame, and double up the bunks ( 4 2"x6") , and instead of carpet, use the bunk slides ( TD69FR ) . My estimate for this approach is about $400. My THEORY is that the 4 eight foot slides will distribute the 1500 pounds of boat over about 2000 square inches, with less friction than the carpet. Your thoughts?

Jesse M. profile picture
Etrailer Expert

Jesse M.

9/29/2026

@PaulG Not a bother at all. I actually like this plan better for what you’re trying to accomplish. Going to the shorter # TD54FR bolster brackets gets the boat closer to the frame, and using four 2x6 bunks with the # TD69FR bunk slides gives you plenty of hull support while reducing the friction you’re fighting with the carpet. With a 1,500 lb boat spread across four 8' bunks, I’d be comfortable with that setup as long as you position the bunks to follow the hull and support it along the same structural areas it rests on now. The big thing is lowering it only as far as you can while maintaining clearance between the hull, fenders, and trailer frame. For your Sea Nymph, I like this plan a lot better than converting the whole trailer over to rollers. I'm always in favor of saving $$$ too.
Paul G. profile picture

Paul G.

10/2/2026

@JesseM Thanks for sharing your thoughts & experience! I ordered eight 8" bolsters & U-bolts to fit the 2.3 crossbeams. I'll pick up some lag screws at the hardware store. I also ordered fore and aft 12" keel rollers & more U-bolts. And, I ordered 2 sets of the PVC bunk slides. I figure the keel rollers are good insurance against banging off the frame, and any weight they take off the bunks is gravy. I picked up four 2" x 6" x 8' PT today-- they're sitting in the garage waiting for the UPS guy to stop by with the rest of it. My intention is to replace the 2 existing carpeted bunks, and add two new ones outboard of those to stabilize the hull and share some of the weight. The V's below are the chines/strakes : ---------V ----------V-- KEEL -- V ---------V ------- Bunk Bunk Roller Bunk Bunk

Video/Article/FAQ this Question was Asked From

Article or Video
Q & A Icon

Continue Researching