Looking For Replacement Axle 3,500lb 90 Hub Face 80 Spring Center With Electric Brakes 5 on 4-1/2"
Updated 09/25/2026 | Published 09/22/2026 >
Products Featured in This Question
Question:
Need part number for Dexter Axle 3500 lb. 90 HF 80 SC with electric brakes and 5 on 4 3/4 wheel
asked by: Steve W
Expert Reply:
Hey Steve,
We don't have an exact 90" hub-face by 80" spring-center Dexter axle, but the closest option is the Dexter Trailer Axle Beam with E-Z Lube Spindles # 7359765. It has the correct 80" spring-center measurement, but the hub face is 95" instead of 90".
That means your wheels would sit about 2-1/2" farther out on each side. If you have enough room under the fenders for that additional width, this would be an option. I would measure your current tire and fender clearance before going this route to make sure the tires will still sit properly within the fenders. You'll want min of 2" on the side of the tire between the fender.
For the 5 on 4-3/4" bolt pattern, you can use two of the Easy Grease Hub and Drum Assembly # AKHD-5475-35-EZ-K.
If you also need new electric brakes, the Dexter Electric Trailer Brake Kit # 23-26-27 includes the left- and right-hand 10" brake assemblies for the 3,500 lb axle.
Let me know if you need anything else or want clarity on anything. Sorry there isn't an all-in-one kit to fit exactly what you're needing, but I'm confident this setup will work for you if the extra 2-1/2" on each side is fine on your trailer.
What kind of trailer do you have, and what are you planning to haul?

Sherman
9/25/2026
In response to Steve W. wanting a 3500lb axle with 90" hub face and 80" spring spacing... This configuration does not make a lot of sense. With a 2" frame width and only a 1/2" clearance tire to frame you would be down to a 175mm section width tire assuming a normal zero offset trailer wheel. so you would be limited to a 175/80-13 load range D tire which will only carry 1650 lbs. So you are limited by the skinny small tires to 3300lbs. Maybe this is what you want, but it seems like a very special and limiting configuration. I think that Dexter wiil make you such an axle but it will be special order and I am not surprised that etrailer does not stock such a thing.
Product Page this Question was Asked From
Dexter Trailer Axle Beam with E-Z Lube Spindles - 95" Long - 3,500 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- No Hubs
- 3500 lbs
- Spindles Only
- 80 Inch Spring Center
- 95 Inch Hub Face
- No Drop or Lift
- Dexter
more information >
Continue Researching
- Q&A: Are Spring Seats Welded On To Dexter Trailer Axle T3584F-EZ-8974
- Q&A: Looking for Pre-Greased 3,500 Idler Hub that is Galvanized for Trailer Axle
- Q&A: Replacing Bent 3,500lb Axle In 2001 Nash 18FM Travel Trailer 6 Lug
- Q&A: Looking for Rust Resistant Replacement Leaf Spring, U-bolt Kit, and Hub for 3,500 lb Trailer Axle
- Q&A: How To Remove Spindles From Trailer Axle
- Q&A: Replacement Trailer Axle For 93" Hub Face To Hub Face Measurement
- Q&A: Replacement Axle, Hubs, and Brakes for 2017 Jayco Jay Flight With Lippert Axle
- Article: Trailer Maintenance Schedule
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Trailer Wiring Diagrams
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: How to Install a Weight Distribution Hitch (With Pictures & Video)
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer


Bart
9/24/2026
You need to double check that lug pattern. A 5on4.75 patten is a very very rare pattern.