Replacement Glass Top For A Magic Craft Stove MCFR17TTB

Question

Question:

I need to replace my mcfr17ttb Magic Craft Stainless Steel Stove top glass cover. Can you please tell me the correct one to order from you? this is the one your website says to order... Is this correct? Furrion Replacement Stainless Steel Top with Glass Cover for Furrion 2-in-1 Range Oven Thank You

asked by: Gregory k

0

Expert Reply:

Hi Greg!

I see you already purchased the Replacement Stainless Steel Top with Glass Cover for Furrion 2-in-1 Range Oven # C-FSRE21SA-SS-003, but I still wanted to get you an answer.

So with that being said, this can be made to fit your Magic Craft MCFR17TTB, but there will likely be a little modification needed. The feedback we have seen when people went with this was that it was off by 1/16 of an inch and the mounting screws needed to be relocated. Unfortunately, I am not sure where or how they were relocated or where it was off by the 1/16".

It also looked like the direct Master Chef replacements are getting pretty hard to come by, so this does look to be your best bet for a replacement.

Sorry I don't have a better answer for you, but I also wanted to make sure you were aware of what to expect.

If you don't mind my asking, what happened to the original glass top?

expert reply by: Lazer S

0

David

7/31/2026

I replaced the glass cover on our Furrion range and it fit perfectly with on modification needed. Took and 5 minutes to install.

Dak

7/31/2026

Every experience I've had with purchases from etrailer has been. This replacement top was no exception. Perfect fit, and not real difficult to DIY. (It would probably be easy for anyone but me, but that's my life story!) You can buy from etrailer with confidence. I will definitely use them again.

Dak

7/31/2026

@Dak....Tried to edit, but couldn't. First sentence shoI'll have ended with the word "excellent" Should have proofread before posting!

Lazer S.

8/3/2026

@Dak Haha! It happens! ^___^ And thanks for the kind words! It is much appreciated!

Keith R.

8/1/2026

This burner top was exact match for my Grand Design 28G Momentum

Michael

8/2/2026

I've had purchases from etrailer each one has been excellent when I submit the perfect part number.This replacement top was a perfect fit, and was easy to install. I would say you can safely buy from etrailer with confidence. They have excellent service and a dependable name.

Lazer S.

8/3/2026

@Michael Thanks for your kind words! ^___^ Did you install this on a Furrion stove or something else?

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Glass Top For A Magic Craft Stove MCFR17TTB

Product Page this Question was Asked From

Continue Researching