Is It Normal for the Anti Rattle Hitch Pin on the Roadmaster RM-195225 to Be Hard to Thread?
Updated 06/19/2026 | Published 06/16/2026 >
Question:
I purchased a Roadmaster Hitch Spare Tire Mount with 2 Receiver Opening - 2 Hitches Part Number: RM-195225 from you a while back and from the first installation on the back of our RV, Ive had to work really hard when threading in the anti-rattle hitch pin to secure the carrier to your RV. It starts off fine, but once I get a little way into the hole for the pin I have to exert a lot of pressure to with a 1/2 ratchet to get the pin all the way in. I have to do the same when removing the pin. Is this normal for this piece of equipment? Thanks!
asked by: Chester C
Expert Reply:
Hi,
I know exactly what you're describing, I have an old bike rack with an anti-rattle that gives me trouble.
The good news is that needing a ratchet to install and remove the anti rattle hitch pin on the Roadmaster part # RM-195225 is normal. These threaded anti rattle systems are designed with tight tolerances to pull the shank snug against the receiver and eliminate movement, so they're often much tighter than a standard hitch pin.
That said, it shouldn't feel like you're damaging the threads every time. One thing that can help is slightly lifting the spare tire carrier while starting the pin. That is the trick that has really helped me. The weight of the carrier can put pressure on the shank and make the holes slightly misaligned, which makes the pin harder to thread. It's also worth checking the threads on both the pin and inside the shank of the spare tire carrier for dirt, rust, or burrs. A quick cleaning and a small amount of lubricant helps.
If the pin starts easily by hand and only gets tight as it draws the carrier snug against the receiver, that's usually a sign the anti-rattle system is working as intended.
Do you ever use any other accessories in the hitch? Do you have any issues with other hitch pins or just the Roadmaster?

Don M.
6/19/2026
I purchased one of these a couple of years ago and it works just fine ! My spare is pretty heavy but this unit handles it well !! Happy with it !
Product Page this Question was Asked From
Roadmaster Hitch Spare Tire Mount with 2" Receiver Opening - 2" Hitches
- Spare Tire Mount
- Hitch Mount
- Universal
- RV
- Standard Finish
- Roadmaster
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: What Size are the Lug Bolts on the Roadmaster Hitch Spare Tire Mount Carrier?
- Q&A: Full Flat Towing Set Up For A 2026 Jeep Gladiator Sahara
- Q&A: Is There a Support Brace Designed for the Replacement Crank Extension for Lippert Spare Tire Winch?
- Q&A: Can the Roadmaster Hitch Mounted Spare Tire Carrier Be Used with E-Bike Rack
- Q&A: Will Roadmaster Spare Tire Carrier Work With Motorhome and Bike Rack
- Q&A: Is TorkLift TL89CR the Same as TorkLift Part A7312S for a 2017 Ford F-350 Dually?
- Q&A: Front Mount Trailer Hitch For 2025 Chevy Silverado 2500 With Most Ground Clearance
- Article: Must-Have Flat Towing Components
- Article: What Is Flat Towing and How to Ditch the Trailer
- Article: Anti-Rattle Devices
- Article: Is It Illegal to Leave My Hitch on My Truck?
- Article: Flat Towing Package for 2015-2018 Chevrolet Silverado/GMC Sierra 3500
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: We Used 34 RV Tow Bars, and These are the Best for Flat Towing



Chester C.
6/18/2026
Thanks Heather. I don’t have any other hitch pins that are as difficult as the one the Roadmaster. I have found that my Makita impact drill does help immensely when I put it on and off now. Thanks for getting back to me and letting me know this was normal.