Does Roadmaster High Riser RO24FR Have Solid or Hollow Shank

Question

Question:

The description for this high low adapter says it has a solid shank, but the pictures sure look like a hollow shank. Which is it? TIA

asked by: Pete

0

Expert Reply:

Hey Pete, I am not sure why the description for the Roadmaster Hitch Riser for Tow Bars # RO24FR says it has a solid shank when it for sure has a hollow one like the pictures show. I will send an update to have the description fixed. Thanks for bringing this to our attention!

expert reply by: Jameson C

0

Hollow Shank
(click to enlarge)

Answer 1

Hi Chris, that’s a great question and I’m glad you’re checking before loading that bike up. With the Roadmaster adapter part #RO24FR being rated at 400 lbs tongue weight, you’d be right at its limit with your bike and carrier, and once you factor in…

view full answer...

Answer 2

Hey Elliot, you can use the Roadmaster Hitch Riser part #RO24FR in the rise position but you can't use it with another hitch extender as that creates too much leverage and movement which would put too much stress on your hitch.

view full answer...

Answer 3

The Roadmaster High-Low Adapter for Tow Bar - 2.5" Hitch - 6" Rise/Drop #RO24FR weighs a total of 14 pounds. It is important to note that any time you use a hitch adapter, you decrease the overall weight capacity of the hitch by 50%.

view full answer...

Answer 4

There are a couple of good anti-rattle options for you, but definitely do not drill a hole into the receiver as it can compromise it. So what you can do is either add a clamp-on style stabilizer, or an anti-rattle hitch pin lock, depending on the…

view full answer...

Answer 5

I have just what you need, a stainless steel locking anti-rattle hitch pin for you. I suggest the Stainless Steel Locking, Anti-Rattle Threaded Hitch Pin for 2" Trailer Hitches part #SR25219. You will need a hollow shank for this to work. For a…

view full answer...

Answer 6

For your 2 inch trailer hitch receiver, when utilizing the Roadmaster Rollaway Trailer Hitch Protector #RM-050, I don't believe the Stainless Steel Locking, Anti-Rattle Threaded Hitch Pin for 2" Trailer Hitches #SR25219 will fit and work…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Does Roadmaster High Riser RO24FR Have Solid or Hollow Shank

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching