Replacement Screen Door Latch for Phillips Doors Dimensions

Question

Question:

What are the measurements of this latch? thank you

asked by: Debbie

0

Expert Reply:

Hey Debbie. The RV Designer Screen Door Latch for Phillips Doors item # RD68ZR measures 2-7/8" long x 1" wide x 7/16" tall. The hand extends 2-13/16" from the body of the latch with the mounting holes spaced 2-3/8" apart.

The strike plate included with the item # RD68ZR measures 2" long x 1" wide with mount holes spaced 1-3/8" apart.

Please note that the Screen Door Latch item # RD68ZR is designed specifically for Phillips Doors.

What kind of screen door do you have?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

RD68ZR
(click to enlarge)

Answer 1

The point of view for left hand/right hand for this door latch is from inside of your camper. The #37211215 would be screwed into the screen door on the outside on the left side (from the inside POV) and the bevel on the strike would allow the latch…

view full answer...

Answer 2

The Door Latch for Philips RV Screen Doors, #37211205 has mounting holes that measure 2-5/16" on center and measures 2-3/4" in height. If you have a Philips-style screen door this is the correct replacement.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Replacement Screen Door Latch for Phillips Doors Dimensions

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching