Troubleshooting Brake Buddy Vantage 2 Remote that Stopped Working

Question

Question:

Have brake buddy vantage 2 , remote quit working , tried syncing , still doesnt, is there someone that works on them? Only used on 3 short trips

asked by: TIM M

0

Expert Reply:

Hey Tim, have you tried re-syncing the remote? If not lets try that first and go from there. Hold (+) and (-) on the unit until "LL" appears, then quickly pressing the Braking Mode and Sensitivity buttons on the remote for 5 seconds to re-establish the link. Let me know fi that makes a difference. You might also check the batteries too.

expert reply by: Jameson C

0

Tim M.

1/14/2026

Have done both

Jameson C.

1/14/2026

@TimM Have verified that the 12 volt socket it's plugged into has power? Sometimes fuses for these can blow.

Tim

1/15/2026

Has new aa battery installed

Jameson C.

1/15/2026

@Tim Any lights on the display? Basically do we know for sure the remote has power as well as the main unit? If so, I would assume the remote probably needs to be replaced due to it being defective.

See All (7) Replies to Tim M. ∨

Answer 1

Hey John, The latch must be worn on your clevis and road vibration is allowing it to slide back down. Hopkins MFG might be able to send you replacement components but they don't offer them for sale, aside from a total replacement of the clevis…

view full answer...

Answer 2

Since you're using it in the proportional mode the Brake Buddy Select 3 #HM39524 really shouldn't be locking up the brakes in the CR-V. After looking into this there are others that have had some similar experiences and have found some…

view full answer...

Answer 3

Did it work at one point and now it stopped or is this the first time you've used it?

view full answer...

Answer 4

It sounds like you're talking about the transmitter that plugs in on top of the Brake Buddy Classic 3 #HM39494. There will be some movement with the transmitter but your description of "very loose" doesn't sound right. When I…

view full answer...

Answer 5

Yes the Replacement Remote #HM39505 will work with your Hopkins BrakeBuddy Vantage Select model number 39504. This remote will alert you if there is a brake away emergency and tell you when the brakes are activated on your BrakeBuddy. You will need…

view full answer...

Answer 6

Yeah, I am not going to be much help without a model number or part number either. If by receiver you mean remote, we have the Replacement Remote for Brake Buddy Select Flat Tow Brake Systems item #HM39505. It works with the Vantage Select, Select…

view full answer...

Answer 7

The wireless remote that comes with the Brake Buddy Select 3 #HM39524 is designed to sit in the cab of your RV and still be able to communicate with the portable system that is mounted in your towed vehicle. You won't need a signal booster to use…

view full answer...

Answer 8

Hey Gary, You'll just need some quick link/safety cable extensions. These can easily be added on while using the #RM23SR and then removed when not. We offer a few different lengths to choose from: 8" cables #RM-910648-8 10" cables…

view full answer...

Answer 9

With the Brake Control #HM39533 for the Brake Buddy Stealth #HM39530 having a hardwire design you will need to modify the Pigtail #C51362 so you will be able to connect it on your 2018 Toyota 4Runner. The pigtail contains the white end which will…

view full answer...

Answer 10

Hey Bob, There is a replacement DC Power Cord for your BrakeBuddy Vantage under part #HM35MV. If you need anything else or help picking out your other flat towing components just let me know.

view full answer...

Answer 11

Hi Merrill! We do have options to adapter your Roadmaster All Terrain tow bar, but the D-rings are going to be the deciding factor. I have the three options listed below: Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars -…

view full answer...

Answer 12

Typically when using D-Ring adapters #BX88357 you'll have to snake some shorter cables, like #RM-910648-20 around the frame rail of the vehicle and then out to the front of the vehicle to connect to your safety cables. There's no easy…

view full answer...

Troubleshooting Brake Buddy Vantage 2 Remote that Stopped Working

Continue Researching