Where is Power Mountain Tallboy Off-Road Bottle Jack Manufactured

Question

Question:

Just want to know where the jacks are made ?

asked by: Rick R

0

Expert Reply:

Hey Rick! The Power Mountain Tallboy Off-Road Bottle Jack # PM94FR is manufactured in China. Let me know if you have any other questions.

expert reply by: Robin H

0

Jacking It Up
(click to enlarge)

Robin H.

12/1/2025

Hey Rick, were you able to pick up the Power Mountain Tallboy jack after learning it’s made in China? Knowing what you decided could help others curious about where their gear comes from.

Answer 1

Gerald, the 12-ton Tallboy #PM94FR weighs about 37 lbs all-in, including the base plate, extensions, and carry bag. It’s a little heavy, but that’s the tradeoff for stability and steel construction - the 9-1/2 inch base plate and solid risers are…

view full answer...

Answer 2

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 3

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 11

Hey George. The Power Mountain Tallboy Off-Road Bottle Jack item #PM34FR is only rated for 6-tons but it's not like you're raising up the entire motorhome. Most of the weight is going to be on the back though and since it is a dually, I…

view full answer...

Answer 12

Hey Mike! The Power Mountain Tallboy Off-Road Bottle Jack #PM34FR can be stored in that manner (with the oil plug facing up), but my contact at Power Mountain stressed that it should only be done for a short period of time, so I recommend setting it…

view full answer...

Where is Power Mountain Tallboy Off-Road Bottle Jack Manufactured

Product Page this Question was Asked From

Continue Researching