Looking For Oval Tail Light With Chrome Bezel

Question

Question:

Hello: Question about Optronics part OPT37FR. Is there a chrome/stainless bezel that will work with this light? Thanks for your time.

asked by: Richard K

0

Expert Reply:

Hello Richard, thanks for reaching out. The Optronics Fusion LED Trailer Tail Light # OPT37FR is only available with a black bezel. I am sorry to say we do not offer chrome or stainless option for this.

We do offer a very similar light that does have a chrome bezel, take a look at the following:

- Piranha LED Trailer Tail Light w/ Chrome Bezel - Stop, Tail, Turn - Red Lens # PE76XV

What kind of trailer is this going on?

expert reply by: Jesse M

0

Piranha LED Trailer Tail Light w/ Chrome Bezel
(click to enlarge)

Richard K.

10/18/2025

Hi Jesse. I am actually looking at these lights for a street rod. I liked the fact that they had the backup light built in. However, I am concerned about weakening the structural integrity of my rear stake pocket by cutting a large oval hole. Hence the desire for a surface mount light. The OPT37R is a fit for these two parameters. Also I have 3/4 round dual function lights with stainless bezels in the end of the bed rolls. An oval bright bezel would be sweet with them. We hot rod guys gotta have our chrome! Pleasure to chat with you, Richard.

Jesse M.

10/20/2025

@RichardK Ok gotcha! Gotta have the chrome haha! I know it isnt Chrome, but I thought you might want to look at the following as a potential option: - GloLight LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - 22 Diodes - Clear Lens # STL1211RCFHPG - Stainless Steel Trim Ring for Optronics Trailer Tail Lights - 6" Oval # OPT82ER

Richard K.

10/20/2025

@JesseM Ok; I'm liking the looks of the stainless bezels. What about the lights in the Installed/In use pix with the red/white lens. Description for bezel says "flange mount". Are those lights STT and backup? Do they require a large oval hole for mounting? Many thanks.

Jesse M.

10/20/2025

@RichardK If you are referring to the pictures on the page for the # STL1211RCFHPG, those all show the same light. The lens is clear but the LEDs underneath are red. It does have STT and backup capabilities. it is considered a surface mount light. It does not require an oval hole for mounting, you would need to have a way to route the wires.

See All (7) Replies to Richard K. ∨

Answer 1

The reverse light pin on a traditional 7-way trailer connector, like part #PK11893 or a factory connector if that's what you have on your 2018 Ram, is the center pin. Take a look at the picture I attached that shows all the pin functions. To add…

view full answer...

Answer 2

Ryan, the BulletProof Hitches Weight Distribution System w/ Sway Control #BPH46VR does not come with a shank, but the shank they'd normally use would be the Weight Distribution Shank for BulletProof Hitches Adjustable Ball Mount #358WEIGHTDIST.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

Hey Michael! When you're choosing a weight distribution hitch the most important factor is the tongue weight of the trailer. It looks like the dry/unloaded tongue weight of a Brinkley Z Air 297 is 924 lbs. Once you add batteries and propane you…

view full answer...

Answer 8

Hey David. The CMB-133-7XL corresponds to a mounting bracket that is designed for a Kodiak 13" disc brake system that fits a #42 Spindle. That spindle is commonly used with 7,000 lbs and 8,000 lbs axles. Which means you'll need the Dexter…

view full answer...

Answer 9

Hello Roy, Looking to swap to disc brakes, you will not be disappointed. Pairing that with the Roadmaster Comfort Ride system makes a huge difference in both braking performance and overall ride quality, especially with a fifth wheel like your…

view full answer...

Answer 10

The GloLight LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 22 Diodes - Oval - Red Lens #STL178RFPB you were looking at is a flush mounted light that bolts directly to your trailer, and only requires a hole for the wiring to pass through.…

view full answer...

Answer 11

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Answer 12

I would highly recommend replacing your worn out Fulton Fold-Away Coupler Hinge Rubber Plugs #F500705. This is going to prevent metal to metal contact between the hinge pieces which will help prevent premature fatigue of the metal. We do not sell…

view full answer...

Looking For Oval Tail Light With Chrome Bezel

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching