How Long Are the Two Sections of the TorkLift PowerArmor Solar Locking Battery Box?

Question

Question:

I would like to fit 2 LiTime 12V 320Ah Mini Bluetooth Lithium Battery for RV and Campinginch in this box or something similar. Their size is L15.12 * W7.64 * H9.76 inches. The box size seems to work, but the center internal bracket may interfere from what I am seeing. Thank you.

asked by: James S

0

Expert Reply:

Hey James. I've linked a dimensional diagram below of the TorkLift PowerArmor Solar Locking Battery Box item # TLA7700LS you were looking at. The length of each section is 13-3/8" so it's not going to work another issue I see is the width. The item # TLA7700LS can accommodate a battery up to 7.625" wide.

My only other option would be the TorkLift PowerArmor Locking Battery Box item # TLA7710R. It has internal dimensions of 58" long x 7-5/8" wide x 12-1/2" tall and will work with Lithium batteries.

What kind of trailer do you have?

expert reply by: Jerred H

0

Solar Locking Battery Box
(click to enlarge)

James S.

10/15/2025

I have a 27' Travel Trailer.

Jerred H.

10/15/2025

@JamesS Awesome! Let me know if you have any additional questions.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

How Long Are the Two Sections of the TorkLift PowerArmor Solar Locking Battery Box?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching