Replacement Temperature and Pressure Relief Valve for a Suburban Water Heater SW6DELC

Question

Question:

Can you please tell me the right part for this water heater. Temperature and Pressure Relief Valve.

asked by: George M

0

Suburban Water Heater Tag SW6DELC
(click to enlarge)

Expert Reply:

Hey George, thanks for reaching out!

The Camco RV Water Heater Temperature and Pressure Relief Valve # CAM10473 you're looking at will work for your Suburban water heater SW6DELC according to my research.

Did your old one just wear out?

expert reply by: Jon G

0

George M.

10/8/2025

Hey Jon, Yes that's right the old one just started to drain just a little once in a while, probably has some debris or sediment around the spring . But bieng just me !OCD LOL!, I will replace. Thank you George

Jon G.

10/8/2025

@GeorgeM Happy to help out however I can! Hey, nothing wrong with taking preventative measures! An ounce of prevention is worth a pound of cure as they say, right?

Answer 1

The Camco Water Heater Element #CAM02143 is what you need for the SW6DEL water heater. According to our research this element will replace the heating element perfectly in your Suburban water heater. You can also use the Camco RV Water Heater Anode…

view full answer...

Answer 2

Hey Rafael, the correct replacement motor for your Kwikee 32 Series Steps is the Lippert Components Kwikee Motor part #LC379147. What RV are these steps installed on?

view full answer...

Answer 3

Hey Susan, welcome back! The Thomas Payne Signature Dinette Cushion #TP36AR is a complete set of four cushions. It includes two seat cushions and two back cushions

view full answer...

Answer 4

Hello Harley, thanks for reaching out. You’ve got a bit of a mixed setup there, and you’re not missing anything, this is just where the Chill Cube system works differently than traditional ducted AC systems. Your front unit is straightforward since…

view full answer...

Answer 5

Hey Bladen, is it possible to use a slightly longer cable? We don't have 36 inch but we do have a 48 cable for a Valterra valve with the part #VAL64GB.

view full answer...

Answer 6

Hello Don, Thanks for writing in! Since you're looking to replace the entire older Voyager VOM-783T system, you will need to run the new wiring that comes with the RV Backup Camera System #VGR95VR. Your original system uses older connections that…

view full answer...

Answer 7

Hi Karen, What are the dimensions of the space available for the fridge? If it's pretty tight the only open we currently have would be the the same fridge #324-000119 (23-1/2"W x 25-3/4"D x 59-3/4"T), but if you have a bit more…

view full answer...

Answer 8

I spoke to my contact at Way Interglobal about the Everchill Refrigerator part #324-000119. They informed me that upon startup and until the set temperature is reached, the unit will draw 8-9 amps. Once the set temperature is reached, it will draw…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Temperature and Pressure Relief Valve for a Suburban Water Heater SW6DELC

Product Page this Question was Asked From

Continue Researching