How Do I Determine What Crossmember And How Many To Install On My 2025 Grand Design
Updated 10/30/2025 | Published 10/07/2025 >
Question:
I have a 2025 Grand Design Momentum 320g with the CRE3000 suspension equalizers and I was looking at adding the x-factor crossmembers for added frame strength, but I am not sure exactly which ones are the right ones for my RV. Do I need to install 4, one at each end of the leaf springs and one in the center axel at the CRE3000, or can I just do the two in the center on the CRE3000s? Can you advise? thanks
asked by: Rick B
Expert Reply:
Hey Rick,
MORyde does recommend going with all 3 crossmembers, one in the front, rear, and middle. The MORyde X-factor # MR33WR is for standard frame hangers with that CRE suspension system like yours. If you only want to install one crossmember to start you want to install this on the center hanger where the equalizers are. I have attached a video of us actually installing this on an older 2020 Grand Design so you can get a better idea as to what it all entails.
Have you been able to get out much in that Grand Design yet?
Product Page this Question was Asked From
MORryde X-Factor Crossmember for Standard Frame Hangers
- Accessories and Parts
- Trailer Suspension Parts
- Crossmember
- MORryde
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: MORryde X-Factor Crossmember for Standard Frame Hangers
- Search Results: trailer suspension parts
- Search Results: reese gooseneck ball
- Search Results: roadmaster shock kit
- Search Results: wheel covers hubcaps
- Search Results: reese goosebox
- Search Results: roadmaster comfort ride
- Search Results: military discounts
- Shop: Dexter Bronze Bushings - Qty 4
- Q&A: Adding MORryde X-Factor to 2023 Grand Design Reflection 337RLS With Roadmaster Comfort Ride
- Video: MORryde Standard Frame Hanger X-Factor Crossmember Installation - 2014 Jayco Pinnacle Fifth Wheel
- Video: Setting Up Your MORryde Standard Frame Hanger X-Factor Crossmember - 2018 Grand Design Reflection Fi
- Q&A: Is the Comfort Ride Leaf Spring Suspension Kit Compatible w/ MORryde X-Factor Crossmembers?
- Q&A: Can MORryde X-Factor and Roadmaster Comfort Ride Systems be Installed Together?
- Shop: MORryde X-Factor Crossmember for LRE, RE, or TRE Leaf Spring Suspension
- Q&A: Does the X-Factor Crossmember for Standard Frame Hangers Require Longer Suspension Bolts?
- Video: Feature Review Lionshead Trailer Wheel Center Cap w/ Snap-In Plug
- Video: Review of Taskmaster Wheel Covers Hubcaps - Stainless Steel Center Wheel Caps - TA46QR
- Shop: Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 4.25" Pilot - Stainless Steel
- Shop: Americana Trailer Wheel Center Cap - Stainless Steel - 4.25" to 4.27" Pilot
- Shop: MORryde GooseTech 5th Wheel to Gooseneck Pin Box for 14K to 18K Trailers w/ Lippert 1621
- Shop: Taskmaster Trailer Wheel Center Cap w/Center Plug - 4.25" to 4.27" Pilot - Stainless Steel
- Shop: Vehicle Engine Heaters
- Q&A: What MORryde X-Factor Crossmember do I Need for My 2022 Grand Design Reflection 31mb 5th Wheel?
- Q&A: Can MORryde X-Factor Crossmembers Be Used With Roadmaster Comfort Ride System?
- Q&A: Can MORryde Crossmember be Used with Roadmaster Comfort Ride System
- Shop: Suspension Enhancement
- Video: Pacbrake Alpha Air Bag Suspension Kit Review and Comparison
- Video: Review of Air Lift Tire Inflator - Portable Tire Inflator - AL79FF
- Video: Feature Review Bug Screen for MaxxAir FanMate Roof Vent Covers



Nick S.
10/30/2025
Hey Rick, how did things go adding the X-Factor crossmembers to your Grand Design? Did the setup with all three crossmembers give you the frame strength you were hoping for? Your update could make it easier for others working on the same suspension system.