Bolt Hole Spacing for the Lippert Replacement Hydraulic Jack Assembly

Question

Question:

LC36VR Jack What is the vertical and horizontal bolt hole spread. Center to center?

asked by: Jeff

0

Expert Reply:

Hey Jeff!

The bolt holes on the Replacement Hydraulic Jack Assembly # LC36VR measure 4-1/2" horizontally and 2-1/4" vertically on center (see attached photo).

Are you looking to replace a damaged jack?

expert reply by: Jon G

0

Bolt Hole Spread on Lippert Hydraulic Jack
(click to enlarge)

Jon G.

9/29/2025

Hey Jeff, did the bolt hole measurements I provided help you with your replacement? I'm asking because your experience could help others who are working on similar projects.

Answer 1

Hello Jerry, Thank you so much for the pictures, they are always most helpful! I am sorry but there is not a seal packing kit, you will need to replace the entire jack. For your Lippert Level Up with part number 343315-RA, you will want the…

view full answer...

Answer 2

Hey Maggie, thanks for reaching out. You’re right to double-check those measurements before ordering anything. The Lippert part #LC36VR is the one most folks end up using on Thor models with system number 0238222, but if your cylinder measures closer…

view full answer...

Answer 3

Hello Terry, thanks for reaching out. The Replacement Hydraulic Jack Assembly for Lippert Level Up System #LC36VR may work for you, but there is no way to look up your RV to know exactly which landing gear leg you will need. RV manufacturers just are…

view full answer...

Answer 4

Hey Dolf. The Replacement Hydraulic Jack Assembly for Lippert Level Up System item #LC36VR weighs 15-3/4 lbs. It ships in a package that measures 30.25" x 12.94" x 11.81". What kind of trailer do you have and where are you forwarding…

view full answer...

Answer 5

Hi Steve, If you have the electric Ground Control 3.0 system #LC358590 or #LC675817 then you would need either the 22-1/2" Left Rear Leg #LC342610 or 24-1/2" Left Rear Leg #LC305339. You'll just want to measure your right rear leg in…

view full answer...

Answer 6

Hey Todd, the Level Best 3000 has been discontinued unfortunately, so you'd need to replace the entire system with something the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941707. This stabilizer will work with frames that…

view full answer...

Answer 7

Hey Keith! I am sorry but we do not sell the replacement Atlas jack for Kwikee Level Best Leveling Systems anymore and do not have a compatible alternative. Lippert's part numbers for them are 359278 for the 10,000 lbs one or 359275 for the…

view full answer...

Answer 8

If the Lippert hydraulic leveling system you have on your 2018 Thor Challenger 37KT is the Level Up system then the correct replacement leg you'd need is the part #LC36VR which fits all positions. If instead you have the Level Best system…

view full answer...

Answer 9

Yes, the Replacement Hydraulic Jack Assembly #LC36VR does have 2 ports on top of the jack for connecting hydraulic lines.

view full answer...

Answer 10

Hello Ian, thanks for reaching out. The part number 2571264 comes back as the Lippert Level Up hydraulic leveling jack. This is an older model that has been discontinued unfortunately, so a replacement hydraulic cylinder is not available. Your best…

view full answer...

Answer 11

The distance the Magnetic Door Holder for RV Doors #OBE37FR the hold the door from the wall is 3-3/8 inches like you can see in the picture I attached.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Bolt Hole Spacing for the Lippert Replacement Hydraulic Jack Assembly

Continue Researching