Looking For Light That Goes With A32RBP Lens Or Suitable Replacement

Question

Question:

Folks, Im looking for the actual light with bulb, mount and wiring that the A32RBP optical lens goes over.

asked by: Howard B

0

Expert Reply:

Hello Howard, thanks for reaching out. I do have a good solution for you, but we do not carry that exact Optronics light that goes with the A32RBP lens. We do however, have a light from Petersen that is virtually identical. Take a look at the following:

- Piranha LED Trailer Clearance or Side Marker Light with Reflex Reflector - 6 Diodes - Red Lens # PE74QV

This is a 4" long by 2" wide side marker light. Looking at pictures of the A32RBP online it looks like almost the exact same thing. The # PE74QV is a complete light so you get bulb, lens, mount and wiring.

What kind of trailer is this going on?

expert reply by: Jesse M

0

Piranha LED Trailer Clearance or Side Marker Light with Reflex Reflector
(click to enlarge)

Howard B.

8/25/2025

Forest River Windjammer Model 3065 WA w/3 Slides

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Answer 10

Hey Gregory, that's really good information. You’ve got a few options, but I wouldn’t jump straight to replacing the leaf springs on a half-ton for that size trailer. Since you’re using a Curt weight distribution hitch, that should be doing most…

view full answer...

Answer 11

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Answer 12

Hey Richard, yes you can set the tension in the springs of the RoadActive Suspension Kit part #RAS3611-Y low enough so that the suspension height is not raised at all. If you add in a lot more tension it will slightly affect the ride height like you…

view full answer...

Looking For Light That Goes With A32RBP Lens Or Suitable Replacement

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching