Dust Cover Recommendation that Fits Trailer with Hub Bore of 1.75 inch

Question

Question:

We need 1.75 greaseable dust cap cover for our trailer. Do you have this item?

asked by: Robert R

0

Expert Reply:

Hey Robert, we have the dust cover part # DX84CR which fits a hub bore of 1.758 inches like it sounds like you need. This is only option we have close to what you mentioned. Did yours fall off?

expert reply by: Jameson C

0

Jameson C.

8/15/2025

Hey Robert, did the Dexter grease cap work out for your trailer? I'm curious because it might help others with a similar need.

Answer 1

We do not have a 1 1/2" grease cap unfortunately. The closest grease cap we carry is the Dexter Grease Cap #DX84CR which has a 1.758" outer diameter.

view full answer...

Answer 2

If the hub bore is 1.5 inches like you mentioned (the area of the hub where the cap installs) then we don't have a Bearing Buddy that will fit. If the measurement was more like 1.75 inch then the #BB1781 would most likely fit as it measures 1.78…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Hi Lee, cool camper! For 2,200 pound axles, you are going to want the Lippert Complete Bearing Kit for 2,200-lb Trailer Axles - L44649 Bearings, L44610 Races #LC23ZP. This includes the bearings, races, seal, cotter pin, and tang washer. It will be…

view full answer...

Answer 11

Hey Scott! The correct bearing kit for your Dexter 6k axle is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you want the Dexter version it is the #DX26ER. What kind of trailer do you have?

view full answer...

Dust Cover Recommendation that Fits Trailer with Hub Bore of 1.75 inch

Product Page this Question was Asked From

Continue Researching