Does The Caliber Bunk Wrap Kit CA98AJ Come With Enough Material For Two Bunk Boards?
Updated 08/15/2025 | Published 07/21/2025
Question:
Does this kit cover only one 16foot board or two? Its confusing because it looks like by the measurements it is for one board but it shows 4 end caps is why I am asking.
asked by: Jimmy K
0
Expert Reply:
Hello Jimmy, thanks for reaching out. The Caliber Bunk Wrap Kit # CA98AJ comes with enough materials to wrap two 8' bunk boards. I suppose you could use it for one 16' board but you would have extra end caps. Plus I am not sure what kind of trailer would even use a 16' bunk board.
expert reply by:
Jesse M
0
CA98AJ
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Caliber Bunk Wrap Kit for 2x4 Boat Trailer Guides - 16' Long - Light Gray
- Boat Trailer Parts
- Bunks
- Bunk Carpet
- 4 Inch Wide
- 16 Feet Long
- Caliber
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Search Results: class ii trailer hitch
- Search Results: caliber bunk wrap
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Installing the Caliber Bunk Wrap Kit
- Video: Install: Curt Trailer Hitch Receiver on a 2019 Subaru Outback Wagon
- Video: Review of Caliber Boat Trailer Parts - Bunk Wrap Kit Boat Trailer 2 x 4 x 16 Light Gray - CA98AJ
- Video: Installing the Draw-Tite Trailer Hitch Receiver on your 2019 Subaru Outback Wagon
- Video: Review of Caliber Boat Trailer Parts - Bunk Wrap Kit Boat Trailer 2 x 4 x 16 Black - CA38AJ
- Shop: Caliber Bunk Wrap Kit for 2x4 Boat Trailer Guides - 24' Long - Light Gray
- Shop: Caliber Bunk Wrap Kit for 2x4 Boat Trailer Guides - 16' Long - Light Gray
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Caliber Bunk Wrap Kit for 2x4 Boat Trailer Guides - 16' Long - Black
- Shop: Caliber Bunk Wrap Kit for 2x6 Boat Trailer Guides - 24' Long - Black
- Video: Installation Guide for the etrailer Trailer Hitch Receiver on a 2019 Subaru Outback Wagon
- Video: How to Set Up Your Curt Trailer Hitch Receiver on a 2019 Subaru Outback Wagon
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Replacement Inner Member for TDE LP8500 Actuator
- Q&A: Best Replacement Motor For Atwood MPD71119
- Q&A: Can You Convert Tie Down Engineering LP8500 from Disc to Drum
- Q&A: How Many Screws Are Included With The Stainless Steel Hex Lag Screw # FA74521?
- Article: Thank you!
- Q&A: Trailer Bunk Carpet for 14 ft long 2x4 Bunk Boards
- Article: The Basics of Boat Trailer Bunks: Bunks or Rollers?
- Article: Where to Position the Trailer Axle?
- Article: Double-Eye Trailer Suspension System Review
- Q&A: How to Determine Hanger Spacing for Tandem Axle Trailer Suspension with 26 Inch Springs
- Article: Trailer Wiring Diagrams
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
Explore Expert Info
![Our Expert]()
on Boat Trailer Parts
on Boat Trailer Parts
Jesse M.
8/15/2025
Hey Jimmy, did you decide to use the kit for one 16' board or split it for two 8' boards? I'm curious because it could help others with similar trailer setups.