Can The Blind Spot Monitoring System CU65XR Be Used On A Car Or SUV

Question

Question:

Can this be used with a car or SUV?

asked by: Steve

0

Expert Reply:

Hey Steve, good question. Technically yes it would be possible to install the Blind Spot Monitoring System # CU65XR on a car or SUV. It comes with a 30' harness so you would have a lot of extra camera wires to deal with. Also you would need to make sure the vehicle has a good, solid, flat mounting location for each camera. They are intended to be installed on a trailer which would have a more or less flat vertical surface to attach to with no obstructions behind.

What kind of vehicle were you wanting to use it on?

expert reply by: Jesse M

0

Blind Spot Monitoring System Camera Example
(click to enlarge)

Jesse M.

8/7/2025

Hey Steve, how did it go with installing the Blind Spot Monitoring System on your vehicle? I'm curious to know if you found a good mounting spot and how it worked out for you. Let me know, as it could really help others in a similar situation!

Answer 1

Hey Brian, the Blind Spot Monitoring System for Towable Campers, Travel Trailers, and 5th Wheels Up to 30' Long #CU65XR that you referenced can give you a blind spot monitoring system but its not going to integrate into your vehicle wiring. It is…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Nice setup Jeff, happy to help! Since you've already ordered the B&W Turnoverball for your 2019 Ram 2500, my recommendation is the B&W Companion Sliding 5th Wheel Hitch #BWRVK3400-5W that's designed for the Turnoverball system.…

view full answer...

Answer 7

Hey Shayne, yes the Gen-Y Hitch Nomad 5th Wheel to Gooseneck Pin Box #GY57ND that you referenced would need the included spacers to install in place of a Lippert 1716 pin box as that pin box is 1/2 inch wider. What camper do you have? At this time…

view full answer...

Answer 8

Hello Chris, thanks for getting in touch. I do have a resource that will help you determine the exact center hole location for your 2019 Ram 2500 with the 6-1/2' bed. Take a look at the instruction manual for the B&W Turnoverball Gooseneck…

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

Hello Levan, thanks for reaching out. Yes, the Gen-Y Hitch Nomad 5th Wheel to Gooseneck Pin Box #GY57ND is made to replace the Lippert 1621 pin box so the bolt hole spacing and dimensions are the same. Your cab and tailgate clearance will be…

view full answer...

Can The Blind Spot Monitoring System CU65XR Be Used On A Car Or SUV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching