Do You Have a Grease Seal for a 1.610 Spindle?
Updated 06/18/2025 | Published 06/14/2025
Question:
i am looking for grease seals for my trailer which appears to be unique because i cannot seem to find seals for them anywhere. The bore size on the hub is 2.360 and the shaft size on the trailer is 1.610. would you have any thing close to this?
asked by: Ronald R
Expert Reply:
Hey Ronald. The closest seal I have that fits your 1.610 spindle is the Grease Seal item # 010-180-00. This fits a inner diameter of 1.68" and outer diameter of 2.33".
I didn't come up with anything for a 1.610 so I am wondering if your caliper is slightly off.
What kind of trailer do you have?
Product Page this Question was Asked From
Grease Seal - Double Lip - I.D. 1.68" / O.D. 2.33" - UFP Axles Prior to 2004 - Qty 1
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.68 Inch I.D.
- 2.33 Inch O.D.
- 3700 lbs
- 4200 lbs Axle
- Dexter
more information >
Continue Researching
- Q&A: Should The Trailer Brake Circuit Have Continuity Between the Blue Power Wire and Ground?
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Shop: Grease Seal - Double Lip - I.D. 1.719" / O.D. 2.565" for 3.5K and 4.4K Axles - Qty 2
- Shop: Grease Seal Kit - Triple Lip - I.D. 1.719" / O.D. 2.565" - 3.5K - 4.2K Axles - Qty 2
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Search Results: trailer axle seal
- Shop: Grease Seal - Double Lip - I.D. 1.68" / O.D. 2.33" - UFP Axles Prior to 2004 - Qty 1
- Shop: Dexter Unitized Oil Seal - Double Lip - I.D. 2.250" / O.D. 3.376" - 7K to 8K Axles - Qty 1
- Q&A: What Size Grease Seal And Dust Cap is Needed on a 3,500 Lbs. Axle With L44649 Outer Bearing
- Q&A: How to Charge a Trailer Battery Through a 7-Way Connector
- Q&A: Replacement for Dexter Grease Seal 010-019-00
- Q&A: Should 12 Volt Hot Lead on 7-Way Trailer Connector Be Hot All the Time, WIll it Drain the Battery
- Q&A: Does 12V Pin on 7-way Trailer Connector Always Have Power
- Q&A: Should There Be Continuity Between Running Lights And Ground Circuit While Bulb Is Disconnected
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel - Qty 2
- Search Results: fender light
- Shop: LED Trailer Fender Clearance Light - Submersible - 2 Diodes - Amber/Red - Driver or Passenger Side
- Search Results: trailer suspension parts
- Search Results: trailer straps
- Search Results: dexter 10 drums
- Search Results: dexter grease seal
- Search Results: door holder
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Bearings Races Seals Caps
Ronald R.
6/18/2025
Thank You for your reply Jerred, The measurement is correct. The trailer is a homemade utility trailer that i purchased a few years ago and it only gets used about twice a year to haul yard waste to the dump. The bearings are fine but the seals were the wrong ones when they were installed. They were forced in and crimped which caused the rubber lip to fail, fortunately i have found the correct seals at 123Bearings. Thank you for your time Ron