2015 Jayco Jay Flight SLX 267BHSW Replacement Brake Kit

Question

Question:

I have a 2015 Jayco Jay Flight SLX 267BHSW Will the TRU36FR work for me? And how many come in an order? Are there two brake hub assemblies per order?

asked by: Steve W

0

Expert Reply:

Hey Steve, thanks for reaching out!

Yes, according to my research the TruRyde Electric Trailer Brakes # TRU36FR will work for your 2015 Jayco Jay Flight SLX 267BHSW.

This kit comes with a pair of brakes, so you need 1 kit per axle.

Are you needing to replace the hubs as well, or just the brakes?

expert reply by: Jon G

0

Steve

6/1/2025

Can you tell me the torque specs for the brake kit and the wheel lug nuts?

Jon G.

6/3/2025

@Steve Trailer brakes don't have a specific torque spec - basically you'll get them as tight as you can by hand without using anything special like a breaker bar. For your wheel lug nuts you'll need to reference the chart in the linked answer page I made for someone else as I don't have a way to add a photo in the comment section at this time.

Helpful Links

question-443226.html

Answer 1

Dexter brand trailer axle components are considered by most people to be the highest quality around. Whenever possible I recommend them over the other brands. For 12 inch diameter Dexter brake assemblies that are self-adjusting the Dexter kit part…

view full answer...

Answer 2

I do have an option but we do not carry hydraulic a-frame trailer tongue jacks. The best option we can offer to replace this is an electric a-frame trailer tongue jack, the Ram Electric Jack part #EJ-3520-BBX or part #EJ-3527-BBX. If you have a…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

2015 Jayco Jay Flight SLX 267BHSW Replacement Brake Kit

Product Page this Question was Asked From

Continue Researching