Recommended Made in the USA Tire Covers for 30" - 32" Tires

Question

Question:

Do you guys have any RV tire covers for 30-32 that are not made in China?

asked by: Dave B

0

Expert Reply:

We sure do Dave! For some tire covers proudly made in the USA you'll want the SnapRing TireSavers RV Tire Covers for 30" to 32" Tires item # ST7002BK. They are sold as a pair.

If you have any additional questions go ahead and throw them into the comment box below and I'll be happy to help you.

expert reply by: Jerred H

0

SnapRing TireSavers
(click to enlarge)

Answer 1

Hi Jeff; there is no maximum tongue weight rating on the etrailer High-Low Fixed Adapter #e25ZV. The adapter is only designed for flat towing, not a trailer or hitch accessory, so it was not tested or given a rating. Are you wanting to use this for…

view full answer...

Answer 2

The Adco Tyre Gard RV Wheel Covers for 18" to 22" Wheels are made overseas. If you're looking for USA made wheel covers I recommend SnapRing TireSavers Tire Covers. The part #ST7006BK for black or part #ST7006WH for white are both made…

view full answer...

Answer 3

Hey Sean, welcome back! We do have a video showing the B&W Turnoverball #BWGNRK1320 being installed on a 2022 Ram 3500. I have provided a link to the video below. We don't have any videos showing how to remove the factory puck system though,…

view full answer...

Answer 4

Hey Mike, our part number #AMP77FR is the same as the Amplock part number #LPC-VR so this is the lock you are looking for and is a really great option. While we don't carry the Proven PL5 I checked it out and while it's a very similar design…

view full answer...

Answer 5

I looked up the Sunset Park RV Sun-Lite 16BH and the official length is listed at 16' 6" therefore in order to find the correct cover we'll need to subtract 3' for the tongue and round up which means we're looking at a cover for…

view full answer...

Answer 6

Your fantastic fan will run off 12V power, so it draw power directly from your deep cycle battery and does not need an inverter. If your water pump requires 110V power instead of 12V, then you can use the Go Power Heavy-Duty Modified Sine Wave…

view full answer...

Answer 7

I don't have quite enough info to determine if you have enough clearance but I don't know where your axle will be located relative to the dimensions you listed. The tire size 215//75R17.5 like part #LHAS701 has a diameter of 30.2 inches which…

view full answer...

Answer 8

Your 235/80R16 tire has a 30.8" diameter so for your application I recommend the Adco Ultra Tyre Gard RV Wheel Covers #290-3972 for tires that are still on the trailer or the Classic Accessories Universal Fit Spare Tire Cover #052963753875 if…

view full answer...

Answer 9

The TDE 46245 you have is a Hub and Rotor for a 3500lb axle and uses inner bearing #L68149 and outer bearing #L44649 and uses the 5 on 4-1/2" bolt pattern For a replacement idler hub you can use the Trailer Idler Hub Assembly for 3,500-lb E-Z…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hey Brian. I have a solution but the hubs on your Sprinter are still going to be too close to the frame even if you switch to a different wheel and tire set up to use the Pacbrake item #PB36RV. These won't work with the way the rear end on your…

view full answer...

Recommended Made in the USA Tire Covers for 30" - 32" Tires

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching