Do the Races Come Pre-Installed on the Kodiak Disc Brakes Kit item # KOD89FR?
Updated 10/22/2025 | Published 04/10/2025
Question:
Installing a KOD89FR hub and rotor assembly in a boat trailer. Are races already installed requiring only the inner and outer bearings to be ped in? Or do you need to install the inner and outer races as well? Thanks for your help!
asked by: Ron S
0
Expert Reply:
Hey Ron welcome back! The races already come installed on the hubs in the Kodiak Disc Brakes Kit item # KOD89FR. You'll just need to slide the bearings in.
If you have any additional questions go ahead and throw them into the comment box below.
expert reply by:
Jerred H
0
Product Page this Question was Asked From
Kodiak Disc Brakes - 12" Hub/Rotor - 6 on 5-1/2 - Dacromet/KodaGuard - 5.2K to 6K - E-Z Lube
- Trailer Brakes
- Disc Brakes
- Marine Grade
- 6 on 5-1/2 Inch
- Hub and Rotor
- 1/2 Inch Studs
- 6000 lbs Axle
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Kodiak
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: titan brake actuator
- Search Results: electric over hydraulic trailer brake controller
- Search Results: brake bleeder
- Search Results: brake fluid
- Search Results: electric~hydraulic brake actuator brake actuator
- Search Results: idler hub trailer hubs and drums
- Search Results: kodiak 225 ss
- Shop: Kodiak Disc Brakes - 12" Hub/Rotor - 6 on 5-1/2 - Dacromet/KodaGuard - 5.2K to 6K - E-Z Lube
- Shop: Kodiak Trailer Hub for 5,200-lb to 6,000-lb Axles - 6 on 5-1/2 - Stainless Steel
- Shop: Kodiak Disc Brake Kit - 12" Rotor - 6 on 5-1/2 - Dacromet and Stainless Steel - 6,000 lbs
- Video: Ultimate Overview of the Kodiak Disc Brakes
- Shop: DeeMaxx Trailer Idler Hub for 6,000-lb Axles - 6 on 5-1/2 - Threaded - Galvanized
- Shop: Kodiak Ceramic Brake Pads w/Stainless Steel Backing Plate - 3,500 lbs to 6,000 lbs
- Shop: Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch, 6" Drop/7" Rise, 18.5K, Cerakote
- Shop: Adapter Module for BrakeRite Electric Over Hydraulic Actuator - OE Ford, GM Brake Controllers
- Q&A: Will the Hydrastar Marine Electric Over Hydraulic Actuator Work W/ a 2018 Ford F-150 XLT
- Video: All You Need to Know About the Kodiak Disc Brakes
- Q&A: Will the Bearing Races be Installed in the Kodiak 12 Inch Hub and Rotor Assembly
- Q&A: Comparing Maxx and Stainless Steel DeeMaxx Disc Brake Kits
- Q&A: Recommended Surge Brake Actuator W/ Drop To Replace 3 Bolt Actuator On Shorland'r Boat Trailer
- Q&A: What Does KodaGuard Coating on Kodiak Disc Brakes Do
- Q&A: Looking for Brake Line Kit that Fits TA96BT 23-27 EZLoader Boat Trailer
- Article: Trailer Wiring Diagrams
- Q&A: Brake Line Kit for Marine Trailers Inc 2678TBH
- Article: 4 Reasons Not to Use RV Solar Power (And 4 Reasons You Should)
- Article: What are the Common Types of Propane Fittings Used on RVs?
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: 4-Step Guide to Installing RV Solar Power
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: How to Bleed Your Trailer Surge Brakes
Jerred H.
10/22/2025
Hey Ron, how did the hub and rotor install go on your boat trailer with the Kodiak kit? Your results could help others setting up the same brakes. Sharing what worked might guide the next person tackling this job.