Axle Lift Kit for a # 10 Torsion Axle

Question

Question:

My trailer has a Dexter torsion axel p-15 SN D 6327757 what lift blocks do I need the bolts measure 8 inches on center

asked by: Vance S

0

Expert Reply:

Thanks for the information Vance! Since your torsion axles have 8" bolt hole centers you'll need the Torflex Lift Kit item # K71-707-02. These lifting blocks are for #10 torsion axles and will give you a 2-5/8" lift.

expert reply by: Jerred H

0

Jerred H.

12/22/2025

Hey Vance, how did the Torflex lift kit work out with your Dexter torsion axles? Knowing how the 2-5/8" lift affected your trailer’s height could help others planning a similar upgrade. Your feedback would be great for anyone with the same axle setup.

Vance S.

12/22/2025

@JerredH those didn’t work I was able to just build my own out of 2 inch square tubing

Answer 1

The #CSS-1145R Coil Sumo Springs you'd looked at would be an economical solution that would improve the rear end suspension sag you're experiencing, but might not remove all the sag depending on the trailer's tongue weight. Since you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The lift kits we carry fit with specific axles; the #K71-725-02 is a tandem axle application and will give a 3-1/8" lift and is compatible with side-mounted #12 Torflex axles with 5,500-7,000-lb capacities. If that is what your axle is, this kit…

view full answer...

Answer 6

Thanks so much for the photo that was super helpful, and what the axle tag shows is that you have a #11 Dexter Torflex axle. We do have the correct lift kit for you, which is the following part: - Torflex Lift Kit - Tandem Axle #K71-724-02 This kit…

view full answer...

Answer 7

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 8

I sent your axle info to Dexter and they were able to determine that you have a set of 7k Dexter Torflex axles so the correct lift you need is the part #K71-725-02 which will give you a lift of 3-1/8 inches.

view full answer...

Answer 9

We offer four different axle lift kits for the Dexter Torflex axles. The difference between these kits is based on the weight capacity of the axle or tandem axles. There will be a tag on the axle shaft that will have the information needed to…

view full answer...

Answer 10

We do have a lift kit for your Lippert 7K torsion axle but the Dexter Torflex Lift Kits like part #K71-725-02 are designed to fit specific Dexter torsion axles. For example, the above mentioned kit will only fit a #12 Torflex axle that has a 5,500 -…

view full answer...

Answer 11

I went out into the warehouse to measure the Lift Kit #K71-725-02 for you. The holes measure 9 inches on center and 9-1/2 inches on center. I've attached a photo to assist.

view full answer...

Axle Lift Kit for a # 10 Torsion Axle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching