Brake Pads/Brake Shoes For Gatormade Trailer With 10,000 lb Dexter Axles

Question

Question:

Hi have a 2022 gatormade 35+5 my gvwr is 24900. I know the wheel hub is oil. I need brake pads can you help me?

asked by: Armando G

0

Gatormade Trailer Sticker
(click to enlarge)

Expert Reply:

Hi Armando,

Thanks for the photo showing the sticker on your trailer, and from what I was able to find you have 10,000 lb Dexter axles with disc brakes. You'll want to verify this just to be certain, but for replacement 10k disc brake pads you can use the Replacement Brake Pads for Dexter Disc Brakes - 10,000 lbs and 12,000 lbs # BP04-395.

The # BP04-395 is for one axle so if you're replacing the brake pads on both axles you'll need to order two (2) of this part.

expert reply by: Kyle S

0

Armando

10/18/2024

Thank you I also forgot to mention I have dually axles and I know they're drums

Reply

Kyle S.

10/18/2024

@Armando Gotcha, so not disc brakes, appreciate you clarifying. Sounds like you're looking for replacement brake shoes then, and the only option we have for 10,000 lb electric brakes are if you have the Dexter Nev-R-Adjust Electric Trailer Brakes - 12-1/4" - Left/Right Hand Assemblies - 10K # 23-438-439. If you have these brakes the replacement shoes are the Replacement Shoe and Lining for Dexter 12-1/4" x 4" Electric Brake Assembly - Left Hand # BP04-325 and Right Hand # BP04-335.

Reply

Answer 1

Since you have replaced your brake assemblies and flexible brake lines, and have bled the system, the sticking brakes on your horse trailer are most likely caused by the electric-over-hydraulic actuator itself or its main steel brake line. It is…

view full answer...

Answer 2

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 3

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Brake Pads/Brake Shoes For Gatormade Trailer With 10,000 lb Dexter Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching