How Far From Wall Does Yakima Rack and Roll Sit When Folded Up

Question

Question:

How many inches does the rack and roll trailer extend away from the wall with wheels attached, and with wheels removed?

asked by: Richard

0

Expert Reply:

Hey Richard, if you leave the wheels on the Yakima Rack and Roll trailer part # Y08106 it would stick out from the wall 22 inches. If you took them off it would be 14 inches since the wheels are 16 inch in diameter.

expert reply by: Jameson C

0

Answer 1

When you store the Yakima Rack and Roll Trailer #Y08106 the trailer will be approximately 6' long. The tongue would be need to be removed when stored so the extension won't add anything to the store height since it'd get removed anyway.…

view full answer...

Answer 2

I called Yakima and they gave me the dimensions of the two ends on the Yakima Tongue Extension Kit #Y08109. The end of the extension that slides out of the extension and into the trailer tongue has an outside dimension of 1-1/2 inches. The other end…

view full answer...

Answer 3

To be on the safe side I recommend the Tongue Extension Kit for Yakima Rack and Roll Trailer, part #Y08109. This is designed to allow you to be able to carry longer boats on the Ranck and Roll Trailer without having to shift the canoe one way or the…

view full answer...

Answer 4

Yes, the 66 inch wide Yakima Rack and Roll Trailer #Y08106 can absolutely carry four kayaks. In fact, if you use cradles - which carries the kayaks on their sides - it can hold up to five kayaks. The Rack and Roll is the best solution because it…

view full answer...

Answer 5

While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and certainly…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

How Far From Wall Does Yakima Rack and Roll Sit When Folded Up

Continue Researching