Looking For 15" Wheel For Wesco Boat Trailer

Question

Question:

Looking for a wheel for my Wesco boat trailer. Tire is 205/75/15 Wesco no longer stocks wheel I have pictures of wheel

asked by: Tim

0

Expert Reply:

Hello Tim, thanks for reaching out. We have quite a few 15" wheel options, so we may have what you need. Go ahead and email me those pictures and I am happy to look into it. There is no way to add pictures to the comments on here, but if you just reply to the email that brought you to this page it will go straight to me.

expert reply by: Jesse M

0

Tim

10/8/2024

Reply and I’ll send pics

Jesse M.

10/8/2024

@Tim Just reply to the email that brought you to this page and it will go straight to me.

Answer 1

The Timbren Axle-Less Trailer Suspension System w Electric Brake Hubs #A35RD545E require a 5 on 4-1/2 bolt pattern and a minimum 14" wheel so the Dexstar Conventional Steel Wheel with Offset #AM20504 will be a compatible fit. This Wheel does…

view full answer...

Answer 2

There are a couple of different ways you can lock the Curt QuickPin No-Latch Trailer Coupler for 2" Ball, either with a standard coupler lock, or you can use a 1/2 inch diameter hitch pin lock, since that is the same size as the pin and clip…

view full answer...

Answer 3

What you have is correct. According to Dexstar, the capacity of the Dexstar Steel Mini Mod Trailer Wheel #AM20539 is 2,860 lbs.

view full answer...

Answer 4

You are correct, they are the same wheels. The Dexstar Steel Mini Mod Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - White Powder Coat #AM20552 is also the 017-233-1W.

view full answer...

Answer 5

On the Curt Coupler #C82CR the two mounting holes are 3" apart on center which you can see in the below diagram. I included a video of AJ installing this coupler for you to check out as well.

view full answer...

Answer 6

To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On #CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video to help as you plan this installation.

view full answer...

Answer 7

Each lamp needs to be grounded either through its mounting studs being in direct contact with the trailer frame or by having a jumper wire ran from the lamp to the trailer frame. Ground the trailer connector at the front of the trailer, which will…

view full answer...

Answer 8

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 9

The valve stem hole of the Dexstar wheel part #AM20532 that you referenced is .453 inches. For a valve stem to fit this hole we have the Americana part #AM20903 as a confirmed fit.

view full answer...

Answer 10

For a valve stem to use with the trailer wheel part #AM20232 you would want the part #AM20906 which has inserts to fit all standard trailer wheels and also can handle up to 200 psi so it will be very reliable.

view full answer...

Answer 11

If your trailer has separate turn signals from the brake lights and you want them to remain that way, you will need to use a special converter. On the trailer side, behind the 7-Way, you will attach the Vehicle to Vehicle Taillight Converter,…

view full answer...

Answer 12

Since LED lights do not require a lot of amperage you can go with relatively small wire. Using 16 or 18 gauge wire will be fine. Harness #A20WB uses 20 gauge wire which is on the small side but certainly not a problem at all for LED lights even…

view full answer...

Looking For 15" Wheel For Wesco Boat Trailer

Product Page this Question was Asked From

Continue Researching