Winch for 2013 Aluma Tilt Car Trailer

Question

Question:

HI, I HAVE A 2013 ALUMA TILT CAR TRAILER AND I WANT TO MOUNT A WINCH ON THE TILT BED. WHAT WINCH AND MOUNTING PLATE DO I NEED..THANKS, JOE

asked by: Joe L

0

Expert Reply:

Hi Joe; for a winch I recommend the Bulldog Winch Trailer Winch # BDW10040. This has a lot of nice features, including a 12,000 lb line pull so it will be able to handle anything you throw at it. This also comes with a universal mounting plate so you don't have to get one separately.

expert reply by: Robin H

0

Robin H.

1/12/2026

Hey Joe, how did the Bulldog winch work out on your Aluma tilt trailer? It sounds like the included mounting plate made setup easier. Sharing how it performed could help others planning a similar setup.

Answer 1

Yes, the Bulldog winch part #BDW10043 has the power unit above the winch which is what the cover part #BDW20191 is designed to fit.

view full answer...

Answer 2

I've contacted Brightway, who forwarded me a copy of the instructions they include with the #BRW77FR switch mode charger. I've provided a clip showing the instructions for you.

view full answer...

Answer 3

I can help you over email if you like.

view full answer...

Answer 4

Thank you for your purchase of the Demco Channel Tongue Trailer Coupler - eZ-Latch. The diameter is 5/16" and the lock that is designed specifically for Demco couplers with the eZ-Latch is the following: - InfiniteRule Lock for Demco eZ-Latch…

view full answer...

Answer 5

While we do have a variety of winch mounting options, I can't say for certain that any of them are a specific replacement for your Aluma Series 82 car trailer. With that being said, we do have a universal winch mounting plate as part #BDW20291…

view full answer...

Answer 6

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Winch for 2013 Aluma Tilt Car Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching