Weight Capacity for the Erickson Big Bed Load Extender

Question

Question:

The description notes a 400 lb.limit. Is that for a bed distributed load or a full load weight?

asked by: John M

0

Expert Reply:

The 400 lb limit would be for bed distributed loads. Basically, if what you are carrying weighs less than 400 lbs the Erickson Big Bed Load Extender # EM07600 that you referenced would work for you.

Check out the review video I attached for this product for you to check out also.

expert reply by: Jameson C

0

Answer 1

The anti-rattle adapter I recommend is the No-Rattle Trailer Hitch Wedge, part #MPG908. This will work for 1-1/4 inch and 2 inch receivers and is designed to insert into the small gap that may exist on your receiver. You then tighten it up after it…

view full answer...

Answer 2

Yes the Malone Anti-Rattle HitchLock System Item #MPG908 will fit the Thule EasyFold XT part #TH903202 which does have an anti-rattle hitch pin. It will pull the rack a little tighter to the hitch tube.

view full answer...

Answer 3

The Big Bed load extender, part #EM07600, has three height settings in 1 inch increments. I went out to the warehouse and measured from the center of the hitch pin hole myself and they're about 17-1/8, 18/-1/8, and 19-1/8 inches to the top of the…

view full answer...

Answer 4

Yes, I have recommend load extenders such as #EM07600 for cars, trucks, vans, and SUVs. Sometimes it is just the right tool for the job! Once installed in the hitch the minimum height is 16 inches. If you measure from the top of the receiver opening…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Beverly. The Replacement Mounting Hardware Kit for Westin HDX Grille Guard with Punch Plate item #W67FR is the correct one for your 2019 Ram 1500. It'll have all the brackets, bolts, washers, and nuts you'll need. The item #W67FR is the…

view full answer...

Answer 8

Hey Dylan, thanks for reaching out. We do carry that 15" aluminum Liger wheel in black. We have them in both a 5-lug and 6-lug. Take a look at the following: - Aluminum Liger Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Glossy Black…

view full answer...

Answer 9

The Air Lift LoadLifter 5000 Ultimate Air Springs with Internal Bumpers part #AL88375 are a fit for a 2019 Ram 1500 Rebel. You can add the Plus Upgrade Kit #AL52301 to get the stainless components.

view full answer...

Answer 10

Ram's will naturally squat a bit more because of the rear coil springs, but if you're dealing with a lot of squat then air springs would be the best option to help get you back to factory ride height. Coil air springs, like the #AL60828HD,…

view full answer...

Answer 11

I am sorry to hear you are having problems with the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL88375. If adjusting your air pressure up and down hasn't helped with the bouncing you may have a spacer problem. Without the right…

view full answer...

Answer 12

For your 2019 Ram 1500 the air bag kit I recommend is the Air Lift part #AL88375 which has internal jounce bumpers in it. I attached an install video for this on a similar Ram for you to check out as well.

view full answer...

Weight Capacity for the Erickson Big Bed Load Extender

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching