What Snappads Should be Used with Lippert Hydraulic RV Landing Gear Feet

Question

Question:

What Snap Pad fits the Replacement Footpad Kit for Lippert Hydraulic RV Landing Gear - 12inch Diameter

asked by: Dave W

0

Expert Reply:

Since the Lippert Hydrauluic Landing Gear Feet are 12 inch in diameter and round the correct Snappads would be the part # SP74FR4.

expert reply by: Jameson C

0

Jameson C.

1/27/2026

Hey, how did the SnapPad XTRA XL pads work with your 12-inch Lippert landing gear feet? Knowing how the fit turned out could help others choosing pads for the same setup.

Answer 1

It sounds like you're trying to replace the motor on your Kwikee steps with the part number 366043, and we have just what you're looking for. In order to replace the motor for these steps you'll want to use the Replacement Motor for…

view full answer...

Answer 2

In regards to Pollak and Hopkins, they are both great options. That said, if OEM parts give you any indication of quality then Pollak would be the better choice as they are the OEM for most manufacturer in regards to trailer connectors. Personally,…

view full answer...

Answer 3

Going by the colors that you mentioned, it sounds like you have the typical set-up, green wire for right turn and brake, white wire for ground, yellow wire for left turn and brake, brown with green wire for right side running lights, and brown with…

view full answer...

Answer 4

Did you have a 4-pin connector that had 5 wires or was it a 5-pin connector? There is a big difference since you normally see a 5-pin connector on a boat trailer with the 5th pin used for an electric reverse lockout solenoid on a brake actuating…

view full answer...

Answer 5

Mike, great question! This drain part #UT69MR is designed for a standard setup with a 1-1/4 inch connection, which typically installs into a sink drain opening around 1-1/2 inches to about 1-3/4 inches wide. The diagram Utopia sent confirms that the…

view full answer...

Answer 6

Hey Rod, thanks for reaching out. Yes, it will! The Curt Helux Shock-Absorbing 5th Wheel Pin Box #C83RJ will indeed work with the Demco Autoslide 5th Wheel Hitch #DM8550038. Just make sure you also use the Demco Autoslide Locking Plate for Lippert…

view full answer...

Answer 7

Hey James, I looked up the specs of your Midnite 150 solar controller and its rated at 96 amps so the correct Victron SmartSolar Controller would be the part #VN34ZR which is rated for 100 amps. What type of batteries do you have and how did you like…

view full answer...

Answer 8

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 9

Hi Martin! You're actually looking at the reducer sleeve I'd recommend. The BTBRV Magnetic Hitch Receiver Reducer Sleeve, Part #BTBRV64FR, is the tightest fitting 2-1/2 inch to 2 inch reducer we carry, and it's my favorite for minimizing…

view full answer...

Answer 10

Hi Sonny, cool camper! The B&W 5th Wheel to Gooseneck Pin Box - Lippert 1621/1621HD - 25K GTW - 3.25K TW #BW73RV will be a great choice! With your 2023 Forest River Sabre 37FLL having a 2,600 pound pin weight, this one will be the better option…

view full answer...

Answer 11

Hey Mike! The etrailer Electric Trailer Jack #e55ZV would be a great replacement for the jack on your 2021 Jayco Jay Flight 242BHS. This has the same lift as your existing jack but with a higher 5,000 lb capacity making it a nice upgrade. It also…

view full answer...

What Snappads Should be Used with Lippert Hydraulic RV Landing Gear Feet

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching