Installing A Replacement Foot Pad For Lippert Hydraulic Ground Control Level System
Updated 08/29/2025 | Published 07/05/2021
Products Featured in This Question
Question:
what order do the steel washer and the 2 o rings go on the bolt? My guess is that the steel washer goes on, and then an o ring, and then the actual foot pad, and then another o ring? And how tight should the bolt be in ft lbs? Thanks!
asked by: Alan B
Expert Reply:
The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 # LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube Item # LT37420 to prevent the bolt from loosening. You are correct with the placement of the washer and o-rings.
Product Page this Question was Asked From
Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1
- Shop: SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 4
- Video: Mount: Replacement Pads for SnapPad Jack Stand Pad System on a 2015 Winnebago Vista Motorhome
- Search Results: winnebago hydraulic leveling system parts
- Search Results: self contained hydraulic jack
- Search Results: rv jack pads
- Shop: Replacement Pad for SnapPad Jack Stand Pad System - 9" Round Jack Foot
- Search Results: 9 inch snap pads
- Search Results: bal leveling system rv jack pads
- Shop: SnapPad StakPad Universal Leveling Block and Jack Pad for RVs and Trailers - Blue - Qty 1
- Shop: Replacement Foot Plate for Lippert Power Gear Hydraulic Jack
- Search Results: trailer tires and wheels
- Shop: Lippert 5th Wheel RV Landing Gear Foot Pad - 9" Round
- Q&A: Recommended Replacement for Atwood GCH6A-10E RV Water Heater
- Shop: MORryde RV Cargo Slide Tray - 90" x 29" - 2 Way Slide - 60 Percent Extension - 800 lbs
- Search Results: jack pads
- Video: Replacement Pad for SnapPad Jack Stand Pad System Spec Review
- Q&A: Solution for Replacement Foot Plate for Lippert Level Up System
- Video: All You Need to Know About the Lippert 5th Wheel RV Landing Gear Foot Pad
- Q&A: Do You Carry SnapPad's that Permanently Stay on the Feet of My Jayco Seneca?
- Q&A: How to Stop Leg From Spinning Installing Replacement Foot Pad for Lippert Hydraulic Ground Control
- Video: An In-Depth Look at the Phoenix Faucets Hybrid RV Kitchen Faucet w/ Pull Out Spout
- Q&A: Replacement Jack Footpad & SnapPads For A 2021 Fleetwood Bounder 33C
- Shop: Suspension Enhancement
- Video: All About the Dometic RV Water Heater
- Shop: Windshield Wiper Blades
- Q&A: Recommended 17.5" Tire/Wheel Combo to Upgrade form 16" Wheel Setup
- Video: SnapPad Jack Stand Pads Installation - 2018 American Coach American Dream Motorhome
- Q&A: Where Does the Blue Brake Controller Wire Connect to on a 6-Way Round Trailer Connector
- Video: Review of SnapPad RV Jack Pads - SnapPad XTRA Jack Pads - SP54FR4
Howard R.
8/28/2025
Hi Kevin - Just received my replacement Lippert 324269 Footpad. I'm sorry, but I need to understand the washer placement. When Alan B says washer first, he means ON THE BOLT not the RV jack, right? So, bolt, washer, O-ring, foot pad, O-ring - bolt it onto the bottom of the jack. RIght? Thanks!