What is the Weight of the 7K Dexter Trailer Axle Beam with E-Z Lube Spindles

Question

Question:

What is the weight of 7000 axel with just spindles in it?

asked by: Gene

0

Expert Reply:

Hey Gene, thanks for reaching out!

The 7K Dexter Trailer Axle Beam with E-Z Lube Spindles # 8327834 weighs in at 58.75 lbs.

expert reply by: Jon G

0

Samuel C.

1/19/2026

Hey Gene, how did things work out with that 7K Dexter axle beam you were checking on? Did the weight and specs line up with what you needed for your setup? Your update could make it easier for the next person with the same question.

Answer 1

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 2

As someone who has thrown quite a bit of hay in his lifetime I can say that all you really need to transport a lot of hay is quality ratchet straps and proper stacking techniques. And for straps, all you really need is 2 of them. If you try an build…

view full answer...

Answer 3

I reached out to my contact at Curt and he said for your 1996 Ford F-150 the Curt Trailer Hitch Receiver #C13902 would require some pretty significant modifications on the truck for installation. Even when considering that the actual custom-fit…

view full answer...

Answer 4

You are exactly right in your findings. The Universal Wiring Kit #ETBC7 will give you a fully functioning 7-Way on your 1994 Ford F-150 once installed. This also includes a 4-Way connection for those smaller trailers you may end up towing as well.…

view full answer...

Answer 5

A 37 inch wide truck frame like what you have on your 1977 Ford F-150 a very common width so for a hitch the B and W #BWHDRH25122 would work really well. The other common frame width is 34 inch but you only see those on cab and chassis trucks that…

view full answer...

Answer 6

The Dexter #T3584F-EZ-8974 axle beam weighs 65 pounds. I have attached a review video.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What is the Weight of the 7K Dexter Trailer Axle Beam with E-Z Lube Spindles

Product Page this Question was Asked From

Continue Researching