Weights of the 36" MORryde RV Cargo Trays

Question

Question:

I cannot find anywhere you indicate the actual weight of the sliding cargo trays. It shows how much they can hold, but not the additional weight you are adding to the RV. Interested in both the 20 and the 26 by 36inch trays.

asked by: Dennis S

0

Expert Reply:

Hey Dennis! I got those weights for you and listed them below:

57.5 lbs - 36" x 20" MORryde RV Cargo Sliding Tray item # MR34FR

61 lbs - 36" x 26" MORryde RV Cargo Sliding Tray item # MR37FR

expert reply by: Jerred H

0

Jerred H.

2/3/2026

Hey Dennis, did those tray weights help you figure out which size works best for your RV? Knowing which one you went with could help others trying to balance storage space and added weight.

Dennis S.

2/3/2026

@JerredH It did help. However, in the end I wound up removing it because it was less useful than I hoped. Lost storage space arrangement options because it was in the way.

Answer 1

*Updated From Below Hi Michael; I'm sure you're right, it is probably prepped for the Furrion. Since Furrion is phasing out the old Vision S, and parts won't be available soon, you want to get the new Furrion Vision S+ Wireless RV Backup…

view full answer...

Answer 2

Hey Mike, it is important that you use the included power cable with the Furrion Vision S+ Wireless RV Backup System w/ 1 Camera #FR57AD like the instructions indicate. If this is like a hardwire install I would look for a cigarette lighter to 2-wire…

view full answer...

Answer 3

I had our warehouse measure the MORryde Sliding Tray for RV Cargo Compartment #MR34FR you were looking at and the inside dimensions are 34-1/8" long x 16-3/4" wide so your 19" wide generator will not fit. You will need to step up to a…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 8

Hi Chuck! The MORryde RV Cargo Slide Tray - 72" x 26" - 1 Way Slide - 60 Percent Extension - 800 lbs #MR67FR sits 1.6 inches above the floor you mount it on. If you want or need it to be a bit higher off the floor, you can also grab the…

view full answer...

Answer 9

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Weights of the 36" MORryde RV Cargo Trays

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching