Replacement Latch for 2002 Featherlite Trailer 4-Horse Trailer

Question

Question:

Hello, we have a 2002 Featherlite 4 horse trailer gooseneck, looking to get replacement latches for. The back doors and side doors. Is this something you sell?

asked by: Deanna D

0

Expert Reply:

Hi Deanna; we do sell replacement door latches like the Bauer Products Manger Door Lock for Horse Trailers # BA95FR. However, we do not know what will fit your trailer. You will need to measure the cutout to find what will fit. For example, this door latch fits cutouts that are 2-3/4" wide x 3-3/4" tall. If this matches what you have it will work for you. If not, you can comment below with your cutout dimensions and I can see what we have available.

I also went ahead and attached a link to all of our trailer door latches which can be filtered by cutout dimensions below for your reference.

expert reply by: Robin H

0

Robin H.

2/3/2026

Hi Deanna, did you get a chance to measure the cutouts on your Featherlite trailer doors? Once you have those dimensions, I can help narrow down which latch will be the right fit. Let me know what you find—I'm here if you need a hand.

Answer 1

The closest door latch we will have is the Redline Full Size Locking Steel Flush Door Latch #L3980. However, this will fit a 3-3/8" x 4-5/8" cut out and will measure 4-1/4" x 5-1/2" so it will end up being too small for your door.…

view full answer...

Answer 2

Since your brake controller is working when you attach to a different trailer and this issue is only occurring when you apply the brakes, we can isolate this issue to the brake wire on your trailer side. Since the brake circuit wire only receives…

view full answer...

Answer 3

RV manufacturers will typically just turn the handle 180 degrees for other orientation and the deadbolt will just be on the opposite side of the plunger. If your deadbolt sits above the plunger on yours and the cutout hole is 2-1/2" to 3"…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Latch for 2002 Featherlite Trailer 4-Horse Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching