Height Of The Stake Pocket Tie-Down Anchor # BR72ZR
Updated 02/17/2026 | Published 06/07/2024
Question:
What are the dimensions of this. I get that it is 4.5inch across but how far is it from where it sits into the slot to the top of the hole the pin goes through underneath? For the other STAKE POCKET ANCHORs there is a dimension picture that shows everything, That is needed for this BR72ZR item as well.
asked by: Roger K
0
Expert Reply:
Hey Roger,
From under the lip of the Stake Pocket Tie-Down Anchor # BR72ZR to the center of the pinhole is 5-1/8".
expert reply by:
Kevin C
0
BR72ZR
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Stake Pocket Tie-Down Anchor - D-Ring - Black Powder Coat - 4,000 lbs
- Trailer Tie Down Anchors
- D-Rings
- Stake Pocket
- Powder Coated Steel
- 4000 lbs
- Drop-In
- Folding
- Brophy
more information >
Continue Researching
- Search Results: stake pockets trailer tie down anchors
- Search Results: battery
- Shop: Brophy Stake Pocket Tie Down Anchor - Black Powder Coat - 2-5/16" D-Ring - 4,000 lbs
- Video: Review of Caliber E Track - L-Track anchor kit - CA36VT
- Shop: Caliber D-Ring Anchor Kit - 5,000 lbs - Zinc - 2 D-Rings
- Shop: Stake Pocket Tie-Down Anchor - D-Ring - Black Powder Coat - 4,000 lbs
- Shop: etrailer D-Ring Tie Down Anchor - Bolt On - 4-7/8" Wide - Square Mounting Holes - 2,000 lbs
- Shop: Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Q&A: How To Test A Lippert Hydraulic Slide/Leveling System Solenoid And Motor
- Shop: Camper Tie-Downs
- Shop: Brophy Stake Pocket Tie Down Anchor - Black Powder Coat - 3" D-Ring - 4,000 lbs
- Shop: Caliber Trailblazer ORV Tie Down Kit - 3,300 lbs - 4 Anchors
- Video: All You Need to Know About the Brophy D-Ring Tie Down Anchor w Backing Plate
- Search Results: trailer stake pocket
- Q&A: How to Determine if T55B Stake Pocket Tie-Down Anchor will Fit Bri-Mar T712-6 Flatbed Tilt Trailer
- Q&A: Replacement Motor for a Lippert LCI 650187 Hydraulic Pump Assembly
- Search Results: stake pocket d rings
- Q&A: How To Determine the Correct Replacement Solenoid for RV Hydraulic Slide-Out On a Keystone Raptor
- Q&A: How to Test Slide-Out Solenoid
- Q&A: Is Solenoid of Replacement Hydraulic Pump Motor # LC167576 Only Available As Complete Unit
- Q&A: Wiring Diagram for the Lippert Polarity Reversing Solenoid LC118246
- Video: The Low-Down on the Brophy Stake Pocket Tie Down Anchor
- Search Results: load binders
- Video: A Closer Look at the B&W Companion OEM 5th Wheel Hitch with Slider
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
Explore Expert Info
![Our Expert]()
on Trailer Tie Down Anchors
on Trailer Tie Down Anchors
Brooke M.
2/17/2026
Hey Roger, did that 5-1/8 inch measurement give you the detail you needed for the stake pocket anchor? Sharing how it worked out could help others trying to confirm the same fit.