Is There Torque Spec for Leaf Spring Center Tie Bolt part # 38-3TB

Question

Question:

Hello, what is the torque on a 3/8 center bolt? Also, what is the torque on a 1/2 u-bolt? Thanks, Mike

asked by: Mike R

0

Expert Reply:

Hey Mike, there isn't a torque spec listed for the Leaf Spring Center Tie Bolt part # 38-3TB so best option is hand tight with hand tools.

expert reply by: Jameson C

0

Answer 1

Hey Robert, I'd be more than happy to help you find the correct leaf spring replacements for your 2017 Heartland Landmark 365 Oshkosh! According to my research your trailer should be equipped with 7K axles so the 6-Leaf Double-Eye Spring #e64SR…

view full answer...

Answer 2

Thank you the pictures are a great help. I recommend using the MORryde AllTrek 4000 Equalizers #MR29DR with the MORryde Suspension Upgrade Kit for Triple Axle Trailers - 3-1/8" #MR26ZR for your 2015 Keystone Carbon 327 5th wheel camper. These…

view full answer...

Answer 3

On square axles, there is traditionally a hole that the leaf spring has a nub that fits in to act as that securing point that a spring seat on round axles would and then the u-bolts secure the axle to the springs. You can see this on the CE Smith…

view full answer...

Answer 4

Square axles normally don't have spring seats like a round axle but do have a hole for the leaf spring bolt to fit into. Take a look at the CE SMITH #CE33201GA-HUB for a visual. The U-bolt mounting kits will have a hole in the center for the…

view full answer...

Answer 5

For the spring eye you would use the Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long #166079, but slipper springs don't have the second spring eye, so a bolt is not used on the back end. You can also use a wet bolt like…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Is There Torque Spec for Leaf Spring Center Tie Bolt part # 38-3TB

Product Page this Question was Asked From

Continue Researching