How Far Will The Kwikee SuperSlide I RV Storage Slide Out Tray Come Out?

Question

Question:

how long does the drawer come out?

asked by: Bechu J

0

Expert Reply:

The Kwikee SuperSlide I RV Storage Slide Out Tray Assembly # LC370774 latches in 3 different positions. Fully closed, 1/3rd open and 2/3rds open. So at most it would extend from the end 46" as it is 70" overall length.

expert reply by: Bud M

0

Answer 1

Lippert didn't have the dimensions for how far out the Rail Kit for Kwikee SuperSlide II RV Storage Slide Out Tray Assembly #LC370762 extends in either direction so I had one pulled from stock and did a bit of testing. On one end of the assembly…

view full answer...

Answer 2

Thank you so much for all off the information! All of the things you found mean you need the 33" Wheelbase MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR. Since your current leaf springs are 14+ years old that would explain why your…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How Far Will The Kwikee SuperSlide I RV Storage Slide Out Tray Come Out?

Product Page this Question was Asked From

Continue Researching