Mounting Hole Dimensions on Sliding Under Platform Pontoon Boat Ladder

Question

Question:

what the the mounting hole dimensions?

asked by: Ryan

0

Expert Reply:

If you're wanting the size of the pre-drilled mounting holes on the # 315-FOG4 they are 1/4". If you're looking for the distance between the mounting holes I have attached a diagram below showing the measurements.

expert reply by: Robin H

0

Ladder Measurements
(click to enlarge)

Answer 1

I looked up pictures of Baja Outlaw 25 boats on trailers and since the boats are taller the size of guide ons were taller options like the CE Smith part #CE27636 which is 75 inches tall.

view full answer...

Answer 2

The Taylor Made StepSafe Dock Steps - Triple - 25-1/2" Tall - 300 lbs - White #TM85ZR is the largest that we currently carry in this style. I may have a few other options that will work for you, but they will be quite a bit different. The first…

view full answer...

Answer 3

The Roadmaster Quiet Hitch #RM-061 that you referenced (and many similar items) are intended for use only when flat-towing a vehicle, but are not suitable for use with a trailer. One option that you can try is the Malone #MPG908 Anti-Rattle system.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Mounting Hole Dimensions on Sliding Under Platform Pontoon Boat Ladder

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching