Fat Tire Trays For Swagman E-Spec Bike Rack

Question

Question:

Hello, I have a Swagman Espec bike rack 2 bike which is 4-5 yrs old. Do you sell the Fat tire trays that would fit this rack? Thank you

asked by: Steve

0

Expert Reply:

Hi Steve,

We do indeed have fat tire wheel trays for your Swagman E-Spec Bike Rack. The correct part for your rack is the following:

- Fat Tire Adapter Kit for Swagman G10 and E-Spec Bike Racks # S64679

expert reply by: Kyle S

0

Answer 1

The best trailer hitch option we offer for travel trailers is the Adjustable Width Trailer Hitch Receiver for RVs part #13703 as it's very universal and can fit pretty much any trailer due to the adjustable frame brackets and crosstube. It has a…

view full answer...

Answer 2

While the Swagman Bumper Mount Racks, parts #S80600 and #S80605, do give you some mounting options, these are designed for lighter 30 lb bikes so the bars that hold the bikes up aren't really designed for heavier 60 lb e-bikes. Since this is the…

view full answer...

Answer 3

It sounds like you need the rivet nuts #RP58507. If the rivet nuts do not work then you can go ahead and drill all the way through the frame and use longer bolts to bolt the dual-cam brackets to the trailer. Also make sure that the set screws at the…

view full answer...

Answer 4

I reached out to my contact at Reese and you are correct that you will need new rivet nuts #RP58507 to install your Reese Dual Cam Weight Sway Control #RP26002 on your new trailer. He mentioned that the replacement thread forming screws #58437 can be…

view full answer...

Answer 5

Sounds like one of the Rivet Nuts part #RP58507 of your Dual Cam Setup part #RP26002 is turning instead of allowing the bolt to come out. You might try tightening down the other bolts again to see if the bracket putting more pressure on the top of…

view full answer...

Answer 6

To determine the amount of drop you'll need your replacement shank to have, take a height measurement from the top inside edge of the receiver tube to the ground, then measure from the bottom of the trailer's coupler to the ground (make sure…

view full answer...

Answer 7

First, if the hole has become enlarged making the bolt loose or damaging the threads, this could indicate that the system is overloaded. Make sure to stay within the capacity of the system to avoid damage. Taking excessively tight turns can also have…

view full answer...

Answer 8

Thank you for your photo of your Reese Dual Cam Weight Distribution system's cam mount. I spoke to my technical contact at Reese about the issue you had with the hardware and dual cam brackets coming out of their mounting positions on your…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Fat Tire Trays For Swagman E-Spec Bike Rack

Products Featured in This Question

Continue Researching