Availability Of Rebuild Kit For Kodiak 2550 Caliper

Question

Question:

Can I use the rebuild kit for a Kodiak 2250 caliper

asked by: Gregory F

0

Expert Reply:

Hello Gregory. The Caliper Rebuild Kit # BP18-075 is only compatible with the 10K - 12K rated Dexter calipers, so I cannot recommend using this for your Kodiak 2250 calipers. Unfortunately, we do not offer a repair kit for the Kodiak 2550 calipers at this time so we would have to recommend replacing the caliper entirely.

expert reply by: Jesse M

0

Answer 1

There is not any melting that is done to keep the dust seals on, but they may have used an adhesive of some sort. Normally they are just a tight fit and a small flat head screwdriver can be used with a rubber mallet to remove it. Most of the time you…

view full answer...

Answer 2

Hey Clifford! The Dexter pistons won't be compatible with the AL-KO since they have a larger diameter. For the calipers you need the #BP18-050 and #BP18-060. We no longer have the AL-KO pistons but it looks like they're out there at a few…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Availability Of Rebuild Kit For Kodiak 2550 Caliper

Product Page this Question was Asked From

Continue Researching