Can Lippert Smart Jack Control Panel Be Replaced

Question

Question:

Can the touch pad on the Smart Jack be replaced?

asked by: Rick S

0

Expert Reply:

Unfortunately, the only way to replace the control panel on the Lippert Smart Jack # LC643589 is to replace the entire jack. According to Lippert, the only replacement parts for the jack are the hardware like the pin or the footplate along with the override plugs # LC733925.

expert reply by: Robin H

0

Rick S.

4/8/2024

I’ve already ordered a new jack. I saw yesterday, after I sent my question in the FAQ area where you had to replace the entire jack.

Answer 1

There isn't an add-on fan kit available for your Ventline E-Z Lift Ventadome Trailer Roof Vent #V3092-601-00, but you could still get the motor and fan blade from their 12v models and try to attach it to the support for the lift arm. The motor…

view full answer...

Answer 2

The overall dimensions I'm seeing for the Dometic RM7732 show it being 59-5/8" tall x 33-9/16" wide x 25-15/16" deep. While we won't have a prefect fit we do have the Everchill RV Refrigerator w/ Freezer #324-000119, which can…

view full answer...

Answer 3

Most trailer jacks like the Lippert #LC285318 only use one wire. That wire provides the power and the assembly grounds through the mounting hardware of the jack. It's hard to tell what's going on with the electric tape and splice connector I…

view full answer...

Answer 4

You could technically wire an electric trailer jack directly to your truck's battery, but that isn't really the most practical setup. I've seen one guy pull out his jumper cables every time he wanted to use the jack in this fashion, but I…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hey Chris congrats on the new truck! I did some research and the HappiJac Camper Tie-Downs item #LC236326-205221 is exactly what you need for your 2026 Ram 2500. I'm working on getting our website updated as we speak. This kit includes both front…

view full answer...

Answer 12

Hey Gary, yes we have Torklift camper tie downs that fit your 2025 Ram 2500 short bed with the part #TL73NR. What kind of camper do you have?

view full answer...

Can Lippert Smart Jack Control Panel Be Replaced

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching