USA Made Bearing Kit For An AL-KO 4,400 lb Axle

Question

Question:

I have a 2013 Keystone Vantage 19 the axles are ALKO 4400# I am looking for the correct axle bearing seals and bearings ie bearing kit. Prefer USA made no China. Thank You.

asked by: Carl C

0

Expert Reply:

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit # TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

expert reply by: Jesse M

0

Answer 1

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 2

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 3

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 4

The Dexter DX7.5L A-60 Actuator #DX56FR you have is designed to be mounted on the end of the trailer frame as seen in the image below. Based on how your actuator was mounted the Actuator #DX89FR would best install like your current actuator. If you…

view full answer...

Answer 5

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 6

To replace your TDE Model LP7000 actuator, I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout item #DX89FR. This coupler is designed to mount on top of a standard 3" wide trailer tongue. It measures right at 3-3/8" wide so…

view full answer...

Answer 7

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 8

What's up, Chuck? You can definitely use higher-rated springs for your trailer, and for that I recommend checking out the 25-1/4" Long 4-Leaf Double-Eye Spring for 4,400-lb Trailer Axles #DX95CR. Be sure to change out the leaf springs on…

view full answer...

Answer 9

If the axle tag on the trailer does not include the axle capacity then you'll have to pull the hubs and either measure the bearings and seals or record their part numbers. The most common bearing combo is a L68149 (1.378" inner diameter) and…

view full answer...

Answer 10

The correct bearing kit for a Dexter 4,400 lbs axle is item #BK2-100. The Dexter 4,400 lbs axles use the same bearings and seals as a Lippert 3,500 lbs axles. This kit includes inner bearing item #L68149, inner race item #L68111, outer bearing item…

view full answer...

Answer 11

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 12

In most cases, you can just simply add brakes to the existing axle and you don't need an entire new axle. That said, this is all based on the axle capacity and I don't have any way to look this up for you. If you have a 3,500 lb axle for…

view full answer...

USA Made Bearing Kit For An AL-KO 4,400 lb Axle

Product Page this Question was Asked From

Continue Researching