Will The etrailer Brake Kit Replace Dexter K23-528-00 & K23-529-00 Brakes?

Question

Question:

Are these replacements for Dexter K23-528-00 and K23-529-00?

asked by: F. H

0

Expert Reply:

The only replacement brakes we have that fit the same AL-KO brake mounting pattern of the K23-528-00 & K23-529-00 brakes are the Kodiak Disc Brake Kit # KD94FR. The AL-KO axles in this capacity used a unique 5 bolt mounting flange which we only carry in the disc brake kit. The Kit # AKEBRK-8 you found only has a 4 bolt mounting pattern.

expert reply by: Bud M

0

Answer 1

The replacement oil cap and oil for the 10K Kodiak Disc Brake Kit - 11" Rotor - 8 on 6-1/2 #KD94FR are as follows: - Replacement Oil Cap #RG04-300 - Kodiak Synthetic Bearing Oil #XLPROLUBE

view full answer...

Answer 2

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 3

The pilot diameter is measured as the diameter of the large hole in the center of the wheel. The Dexstar #AM20790 steel dual trailer wheel you referenced has a 4.88 pilot diameter. So which pilot diameter would you need? To figure that out, I would…

view full answer...

Answer 4

The pilot hole on a wheel is the big center hole right in the middle of the wheel. It fits over the hub.. It can be tough to measure these with the wheel still on the trailer so you will want to remove the wheel and then it will be easier to measure.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Will The etrailer Brake Kit Replace Dexter K23-528-00 & K23-529-00 Brakes?

Product Page this Question was Asked From

Continue Researching