Are There Replacement Master Cylinders Available for Brake Actuators

Question

Question:

I have a 2000 dual axle heritage boat trailer with 4 disc brakes. The coupler on the trailer looks a lot like this. I have been told that the master cylinder is broke on it since the brakes no longer work. Is there anyway to just replace the master cylinder on something like this?

asked by: Jarod S

0

Expert Reply:

Yes, there are replacement master cylinders for surge brake actuators like the Demco Actuator part # DM8203102 that you referenced. If this was the actuator that you have you would want the Replacement Master Cylinder # 5672.

If you have a different actuator I attached a page that has all of the replacement master cylinders we offer.

expert reply by: Jameson C

0

Answer 1

Yes, you can use your DA70 actuator for drum brakes with disc brakes, you just need to switch the master cylinder to the Replacement Master Cylinder for Demco Actuators - Disc Brakes #5672.

view full answer...

Answer 2

I checked with Demco and the Kar Kaddy X part #DM713093 uses DOT 3 or 4 brake fluid.

view full answer...

Answer 3

For you Demco Kar Kaddy SS tow dolly the correct replacement master cylinder is the part #5672.

view full answer...

Answer 4

Yes, you can swap out the master cylinder in your DA66B to convert to disc brakes. Since it does not have a reverse lockout, you actually want the #DM5919 instead of the #5672. The #DM5919 comes with an inline solenoid. You will also need a 5-way for…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Are There Replacement Master Cylinders Available for Brake Actuators

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching