Firestone Ride Rite Air Bag Kits that Fit 2024 Chevy Silverado 2500HD ZR2 Bison

Question

Question:

I was giving the part no 2613 and 2709 could you recheck that 2709 should be the heavy duty air bags and they will work on my 2024 Chevy 2500 ZR2 bison other place say they dont work

asked by: Gary M

0

Expert Reply:

According to Firestone the two Ride Rite kits part # F2613 and the Extreme Duty part # F2709 are both a confirmed fit for your 2024 Chevy Silverado 2500HD ZR2 Bison. I checked with them and they do not have fit exclusions for your truck model.

expert reply by: Jameson C

0

Answer 1

Since you are going to install the Firestone Ride Rite kit part #F2582 the best solution I have for you would be a compressor kit that has an air tank built into it plus an air chock so that you can inflate a tire if needed. For that we have the…

view full answer...

Answer 2

The differences between the Firestone Ride Rite #F2613 and the Red Label #F2709 for your 2023 GMC Sierra 3500 Crew Cab Long Bed is the air pressure and max weight capacity. The Ride-Rite #F2613 are rated for 5,000lbs and 100 PSI, where the Red Label…

view full answer...

Answer 3

Hey Haitham, no the Air Lift LoadLifter 5000 part #AL57341 that you referenced is not a confirmed fit for your 2024 GMC Sierra 2500 AT4X. Instead you'd need to go with the Firestone #F2613.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Larry! Yes, the Onan Generator - QG 7000i Onboard RV Generator #CM44MR is capable of using a remote start. For a standard setup, you can use a switch like #CM86RR along with an extension harness #CM26RR. You can also use the EC-AGS+ Auto…

view full answer...

Firestone Ride Rite Air Bag Kits that Fit 2024 Chevy Silverado 2500HD ZR2 Bison

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching