Front Hitch That Fits 2008 Dodge Ram 1500

Question

Question:

Do you offer a front mount hitch for a 2008 Dodge Ram 1500 4x4 5.7 liter hemi , 6 1/2 bed

asked by: Guy N

0

Expert Reply:

Yes we do have front hitches that fit your 2008 Dodge Ram 1500. We have the part # 31320 which fits regular and quad cab models and the # C31017 which fits the mega cab models.

expert reply by: Jameson C

0

Answer 1

Hey Jay, yes the Draw Tite front hitch part #65046 that you referenced is correct for your 2007 Dodge Ram SLT quad cab 4x4 as long as it's a 2500/3500. If instead you had a 1500 you would want the Curt front hitch part #31320. What are you…

view full answer...

Answer 2

I just spoke with my rep from Horizon Global about the The Draw-tite Front Mount Trailer Hitch Receiver - Custom Fit - 2" item #65033. Due to varying tire sizes, trims, and after market suspensions like yours, they do not offer the measurements…

view full answer...

Answer 3

There is a front-mounted trailer hitch receiver that fits a 2006 Dodge Ram 1500, though the correct one will simply depend on the cab that you have and the model. I will list out the fits so you can find exactly what you need for your truck. - 2006…

view full answer...

Answer 4

We do have a couple of possible options for front mount hitches for your 2008 Dodge Ram 3500 Mega Cab. You can use #65046. There is some minor drilling required, see instructions, but you will likely not have to do any trimming. I have included a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Front Hitch That Fits 2008 Dodge Ram 1500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching