Can You Add a Step to the TorkLift Glow Step Scissor Steps?

Question

Question:

Can I add the TorkLift add a step kit to a 6 step to get 7 steps? The height of my vehicle is 60 and it looks like that combination would fit. Thank you for your time.

asked by: Tim K

0

Expert Reply:

Yes, you can. To add a step to the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear item # TLA7846 you would need the Single Add-On Step for TorkLift GlowStep Kits item # TLA7801.

expert reply by: Jerred H

0

Answer 1

Hey Mike, since we don't have exactly the step cover set that you need your best option would be to go with the part #MR84RV that you referenced and trim down the larger cover to match the size of the rest. You could use a box cutter for this and…

view full answer...

Answer 2

Hello Annette. We do offer an add on step for the TorkLift GlowStep scissor steps. For example, we have the Single Add-On Step for TorkLift GlowStep Kits #TLA7801 which adds a step to the middle of your steps so the rest of the assembly remains as it…

view full answer...

Answer 3

The TorkLift GlowStep Stow N' Go part #TLA7843 are stored on the side of your camper attached with a bracket like in the photo I have attached. They do stick out on the side. You would need the GlowStep Revolution Scissor Step for it to store…

view full answer...

Answer 4

If your 2013 DRV Mobile Suites 38RSSB3 currently has a Torklift GlowStep on it the Single Add-On Step for TorkLift GlowStep Kits #TLA7801 that you referenced would be all that you need to add an additional step. I attached a picture that shows all of…

view full answer...

Answer 5

No they do not, the closest to that measurement that they make is the Single Add-On Step for TorkLift GlowStep Kits #TLA7801 which measures 20" wide and is 8" deep.

view full answer...

Answer 6

If the steps you have are the Torklift Glowsteps that fold down then yes we have kits can add a step like with the Single Add-On Step part #TLA7501 but if you have a different step setup I would need to know what you have to determine if there's…

view full answer...

Answer 7

In regards to the TorkLift GlowStep Stow N' Go Scissor Steps part #TLA7833, there is indeed a 6-1/2" gap between the first/last step and the mounting plate. This is needed in order for the steps to fully retract. It is not the intention of…

view full answer...

Answer 8

The mounting brackets for the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear item #TLA7833 measure 21-1/2" wide x 12-1/2" tall x 8-1/2" deep. The steps will bolt directly to your Lance 2021 1172 Truck Camper with…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can You Add a Step to the TorkLift Glow Step Scissor Steps?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching